Bedienungsanleitung Boretti PRO 100 IX (Seite 11 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

121734

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

the metal grease ﬁlters. (See chapter on ‘Maintenance’).

To reset the 200-hour timer the motor and lights must be switched ‘OFF’.

Push the LED button ‘+’ for 10 seconds.

One ﬂash of the LED lights F and C = function is switched ‘OFF’.

Two ﬂashes of the LED lights F and C = function is switched ‘ON’.

To reset the 100 hours timer back to zero requires the motor and lights must be switched ‘OFF’; then and proceed as follows:

Press the LED button ‘+’ for 3 to 4 seconds and the LED lights F and C will ﬂash to conﬁrm the programme has been reset to

zero.

Instructions for replacing the active charcoal ﬁlter are given in the chapter on ‘Recycling’.

Setup Process

Modiﬁcation: How to adjust the internal microprocessor data to suit the type of motor ﬁtted to this appliance and the

supply frequency of 50 or 60 Hz..

1 - Disconnect the cooker hood from the mains supply.

2 - Push the button 0/1 MOTOR.

3 - Reconnect the mains supply while pushing the button 0/1 MOTOR for at least 2 seconds.

4 - Slacken the button 0/1 MOTOR (the Leds ﬂash for about 3 seconds : capacity’s conﬁrmation SETUP

PROCESS).

5 - During the ﬂashing time select the motor type used while pushing one of the 5 buttons according to the following

board:

BUTTON 0/1 Light : Motor 8/28 & 8/50 220-240 V AC / 50 Hz.

BUTTON 0/1 Motor : Motor 8/28 & 8/50 220-240 V AC / 60 Hz.

BUTTON Speed ( - ) : Motor PRO 220-240 V AC / 50 Hz.

BUTTON Speed (+ ) : Motor PRO 220-240 V AC / 60 Hz.

BUTTON Intensive speed : Motor K40 & K50 220-240 V AC / 50 Hz.

REMOTE CONTROL HANDSET

Caution, the remote control must be ﬁtted with standard LR03-AAA size 1.5V zinc-carbon alkaline batteries as illustrated Fig. 9.

These batteries should give a long life and constant discharge throughout their life.

These batteries must be disposed of properly and could explode if damaged or exposed to heat. Do not dispose of

on ﬁre.

5 USEFUL HINTS

• To obtain the best performance it is advisable to switch ‘ON’ the cooker hood a few minutes (in the boost setting) before

you start cooking and you should leave it running for approximately 15 minutes after ﬁnishing.

• IMPORTANT: NEVER DO FLAMBÉ COOKING UNDER THIS COOKER HOOD

• Do not leave frying pans unattended during use as over-heated fat and oil might catch ﬁre.

• Do not leave naked ﬂames under this cooker hood.

• Switch ‘OFF’ the electric and gas before removing pots and pans.

• Ensure heating areas on your hotplate are covered with pots and pans when using the hotplate and cooker hood

simultaneously.

6 MAINTENANCE

Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply.

The cooker hood must be kept clean; a build up of fat or grease can be a ﬁre hazard.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Boretti PRO 100 IX Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info