Bedienungsanleitung Boretti VP 96 (Seite 77 von 100) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Spanisch)

69423

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

For the Installer

General Installation Instructions

Your Boretti must be installed by a qualiﬁ ed tech-

nician according to legal/locally applicable codes

and ordinances.

Before you start installation or reparation work,

make sure that the range cooker is not connected

to the power source.

Your Boretti can be installed against a wall that is

higher than the counter, such as a tall appliance

cabinet or a closed wall, at a distance of at least

50 mm from the side of the range cooker, as illu-

strated in Drawing A. There must be at least 650

mm of space between the cooktop and any shelf

or hood placed above it.

Your Boretti range cooker has a standard height

of approximately 91 cm. If your Boretti has been

ﬁ tted with round adjustable legs, you can also

purchase these in a taller version. The range

cooker can then be adjusted to a height between

91 and 97 cm. It is recommended to align the

cooktop with the top of the counter. We also re-

commend that the range cooker be perfectly level

in order to ensure proper functioning.

The strip with ventilation slots included with your

range cooker is only mandatory for use with a

ventilated gas oven, and only when it is closed off

on the upper–back side by tiles or a wall. You do

not need to use these for a model with a regular

electric oven; that range cooker can be placed

directly against a back wall or tiles.

In order to ensure proper functioning, we advise

you to use your range cooker in a well–ventilated

area. This is especially important for range coo-

kers that are connected to bottled gas (butane/

propane). Butane/propane (bottled gas) is heavier

than air. As a result, the gas will sink low to the

ground (only in case of leakage). Therefore, there

must be sufﬁ cient ventilation to disperse gas at

ground level. Under no circumstances may the

gas bottles be placed below the living area (base-

ment/crawl space). This also applies to empty or

half–empty gas bottles.

Electrical Connection

Check whether voltage and capacity agree with

the features mentioned on your Boretti’s type

plate. Under no circumstances may this plate be

removed. The fuses and home mains voltage in-

stallation must comply with the range cooker’s

requirements. The connection to the electrical

supply may be either ﬁ xed, or a plug and socket.

In the latter case, the plug and socket outlet must

comply with applicable regulations. The connec-

tion must be grounded, regardless of type. Befo-

re connecting, make sure the electricity source is

properly grounded. Avoid use of reducers, adap-

tors, extension cables or by–passes.

Caution:

See Page 98 for the correct installation diagrams.

All six screws must always be well tightened.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Boretti VP 96 Seite 77

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Boretti VP 96

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info