Bedienungsanleitung Bort BFP-110N (Seite 8 von 104) (Alle Sprachen)

555164

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

• SWITCH OFF WHEN NOT SPRAYING - Avoid run-

ning the unit with the ﬂ ow rate knob fully closed for

any length of time.

We accept no responsibility for damage caused by

the use of unsuitable substances, or paints that hare

not been thinned correctly, and any health hazards

that arise from lack of adequate ventilation

IMMEDIATELY SWITCH OFF THE SPRAY

GUNWHEN:

• Interruption in the mains plug, mains lead or mains

lead damage.

• Defectswitch.

• Smoke or stench of scorched isolation.

OPERATION INSTRUCTIONS

PREPARATION B

Do not use textured wall paints or coatings as

this wHIblock the nozzle.

To obtain the best results, it is important that you pre-

pare the surface to be sprayed and thin the paint to

the correct viscosity, before you operate your spray

gun. Always ensure that the surfaces to be sprayed

are free from dust, dirt and grease. Make sure that you

have masked the areas that should not be sprayed,

using a good quality masking tape. The paint or ﬂ uid

to be sprayed should be thoroughly mixed and free

from lumps or other particles. Many substances can

be sprayed with your spray gun, but always check the

manufacturers recommendations before purchasingy-

our paint.

THINNING

Always rememberto disconnect from the

mains sup-ply before ﬁ lling the paint contain-

er with sprayable material.

Most paints are supplied ready for brush application

and will need to be thinned before they are suitable to

be sprayed. Follow the manufacturers advice on thin-

ning the paint when used with a spray gun. The viscos-

ity cup will help you to determine the correct viscosity of

paint to be used. To determine the correct viscosity, ﬁ ll

the cup to the brim with the paint. Measure the amount

of time it takes for the cup to empty back into the can.

The table below shows recommended times for differ-

ent types of material.

Plastic & latex paint 24 - 28 seconds

Water based paint 20-25 seconds

Primers 24-28 seconds

Varnishes 20-25 seconds

Oil based paints 18-22seconds

Enamel paints 18-22seconds

Aluminium paints 22-25 seconds

Carundersealing 25-35 seconds

Wood sealers 28-35 seconds

Wood preservatives Nothinningrequired

Wood stains Nothinningrequired

If the paint takes longer than the recommended time to

empty, then further thinning is required. Mix in a small

quantity of the appropriate thinner and use the viscos-

ity test until the correct thickness is achieved. Some

sprayable materials contain particles and lumps. These

materials should be strained before ﬁ lling the paint con-

tainer.

SPRAYING C

Fill the paint container with the correctly thinned and

strained paint. Connect the spray gun to the mains

supply. Aim the spray gun at a piece of scrap material

and operate the trigger switch until paint is spraying.

Adjust the output control

until the required

volume of paint is spraying. Turn the output control

in a clockwise direction (B) to reduce the ﬂ ow and

anti-clockwise (A) to increase the ﬂ ow. Adjustment of

the output control will affect the spray pattern. A poor

spray pattern will concentrate the paint in the centre

of the spray and give a blotchy ﬁ nish. A good spray

pattern will give even distribution of paint throughout

the pattern.

SPRAYING TECHNIQUES D

To obtain the best results, keep your spray gun level

and parallel to the surface at all times.

Keep the nozzle 25 - 30 cm from the surface and spray

evenly from side to side or up and down. Do not spray

at an angle as this will lead to paint runs on the surface.

Use smooth and even strokes. When spraying large

areas, use a criss-cross pattern as shown.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bort BFP-110N Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info