Bedienungsanleitung Bort BFP-450N (Seite 5 von 20) (Englisch)

555168

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Electric spray gun

Read all instructions and product labels. When using

electrical tools, follow all precautions to reduce the risk

of ﬁ re, electric shock, and other personal injury.

TECHNICAL SPECIFICATIONS 1

OPERATION INSTRUCTIONS 2

IMPORTANT SAFETY INSTRUCTIONS

WARNING!

When using electric appliances, basic pre-

cautions should always be followed, including the fol-

lowing:

• Read all the instructions before using the appliance.

• To reduce the risk of injury, close supervision is nec-

essary when an appliance is used near children.

• Only use attachments recommended or sold by the

manufacturer.

• To disconnect, turn all controls to the off (“O”) posi-

tion, then remove the plug from outlet.

• Do not unplug by pulling on cord. To unplug, grasp

the plug, not the cord.

• Unplug from outlet when not in use and before servic-

ing or cleaning.

• Do not point the paint roll or accessories toward your-

self; danger of injury by ejected material.

• The unit is not a toy; keep it away from children.

• Power cable and power plug must be undamaged.

Replace damaged parts immediately.

• Never submerge the unit in liquid!

• Do not use hot water for rinsing out and cleaning.

• The unit may not be used in workplaces bound by the

explosion-protection regulations.

• If the supply cord is damaged, it must be replaced by

the manufacturer or its service agent or a similarly

qualiﬁ ed person in order to avoid a hazard.

Materials to be processed:

Dilute dispersion paints and latex paints for interior and

exterior walls.

Materials not to be processed:

Paint and lacquers containing solvents and materials

containing heavily abrasive components.

INSTALLATION AND OPERATING

• Assemble the paint roll (ﬁ gure 1).

• Mount deaeration unit, connect hoses (ﬁ gure 2): slide

suction hose (B), paint feed hose (A) onto the respec-

tive connection pieces until they stop. Slide on screw

sleeves and tighten.

• Before beginning work, cover or tape up the ﬂ oor, fur-

niture, door frames and other objects. Place the unit

on a sufﬁ ciently sized piece of plastic or cardboard.

• Stir the paint well and thin up to 10% if necessary

(observe information from manufacturer).

• Submerge suction hose with suction ﬁ lter (ﬁ gure 3)

to the bottom of the paint container and fasten to the

paint container edge with clamp.

• Turn the control knob to the “working” position. (ﬁ gure

4) The pressure in pipe B will reduce when it exceeds

the set value.

• Open dosage valve at handle. Switch unit on (ﬁ gure

5). Suction and paint feed hoses and paint roll ﬁ ll with

paint in appox.2 min. The unit is ready for operation

when the ﬁ rst drops of paint emerge. Set the paint

feed as required using the dosage valve.

ATTENTION! Air in the suction hose or pump area can

lead to suction and function interruptions. Ensure that

the suction ﬁ lter is always completely covered with

paint. Reﬁ ll paint in a timely manner, set the paint con-

tainer at an angle or prepare a new paint container.

Switch off the unit before moving the suction hose to a

new paint container.

BREAKS DURING WORK

Immediately stop

Press down the button (ﬁ gure 6), the paint roll will be

stopped ﬁ lling with paint until the valve is opened (ﬁ gure

7).

Short breaks (up to four hours):

• Switch off paint pump and open dosage unit in han-

dle.

• Insert paint roll into plastic bag immediately and tie it

up to airtight (ﬁ gure 8, A).

• Leave suction and air bleed hoses in the paint.

Long breaks (days):

• Place paint roll in a bucket of water (ﬁ gure 8, B).

• Wet the paint surface in the paint container with some

water to prevent a skin from forming.

• Used accessories which are already unscrewed are

to be placed into water immediately after use.

CLEANING

• Switch off the appliance and scrape off paint roll over

the paint container.

• Remove paint roll by snapping it from the roller frame

and clean it thoroughly separately. Detach the seal-

ing cap of the paint roll with a suitable tool. Detach

paint roll and clean all parts in lukewarm water.

• Put the suction hose A into a container which is ﬁ lled

with clean water.

• Switch on the appliance and pump water for about 10

minutes. Shut down ﬁ g6 and open the valve ﬁ g 7 for

8 times during the pumping. Each closed time should

not less than 15 seconds.

• Disconnect the aluminum hose and clean it separate-

ly.

ATTENTION! When storing, always leave the dosage unit

in the handle in the open position (Figure 5).

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bort BFP-450N Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info