Bedienungsanleitung Bort BHG-2000U-K (Seite 3 von 44) (Alle Sprachen)

555178

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Hot air gun

CAREFULLY READ THE INSTRUCTIONS BEFORE

YOU USE THE HOT AIR GUN!

1. ADDITIONAL SAFETY RULES

BEFORE USING THE APPLIANCE:

1. Check the following:

- Make sure the voltage of the hot air gun corresponds

with the power voltage.

- Are the mains lead and the mains plug in a good

state: strong, without ravels or damages.

2. Avoid the use of long extension cables.

3. Do not use the appliance under moist circumstances.

4. The metal mouthpiece gets hot. Watch out and do not

touch the metal mouthpiece.

5. Prevent damage of the heating element. Do not lock

or block the mouthpiece.

6. Do not leave the appliance when switched on.

7. When the appliance is not in use, it can be put away

on the collapsible support, which is on the air gun. By

collapsing this support, the air gun can easy be put

away on it. The hot air gun now stands on the support

with the mouthpiece up.

8. Do not use the appliance for drying hair or for drying

living human beings in general.

9. Do not use the appliance in a bath, above water or in

spaces where easy inﬂ ammable liquids are used.

Warning! This appliance operates at a temperature

of 200-600 degrees without visible signs of this

temperature (no ﬂ ames); still there is a chance of

ﬁ re risk. Watch out for the hot air stream from the

mouthpiece. This air stream can cause burns.

WHEN OPERATING THE APPLIANCE:

1. If you are going to use the hot air gun, vapours and

gas can be liberated during a short time. This can

be harmful for your health. Asthmatics can suffer hin-

drance of it.

2. Before connecting the plug to the mains voltage you

have to check if the switch is in position “0”.

3. Keep the mains lead always away from the mouth-

piece of the hot air gun.

4. Keep children and animals away from the appliance

if you are using it.

IMMEDIATELY SWITCH OFF THE APPLIANCE WHEN:

1. plug and/or cable are defective or damaged;

2. the switch is defective;

3. you smell or see smoke caused by scorched insula-

tion from the hot air gun.

2. INSTALLATION

You can work manually with this hot air gun or you

can put it in a vertical position. If you use the vertical

position the metal suspension bracket of the handgrip

must also stand vertical for supporting the handgrip on

the correct place.

3. USING THE APPLIANCE

THE HOT AIR GUN CAN BE USED FOR:

• plumbing work like tube connections, solder, bowing

tubes;

• removing paint, varnish and lacquer without ﬁ re-risk;

• quickly drying of appliances which have become wet;

• drying surfaces for quick repairing;

• removing self-adhesive labels in a clean way;

• placing PVC labels;

• blistering after sticking PVC materials can be smoo-

thed after heating;

• easy removing of vinyl carpeting;

• forming all synthetics with a low temperature among

which polyethylene and PVC;

• forming all synthetics with a high temperature among

which acryl and plexiglass;

• smelting synthetics, among which matters and foils

with PVC layer;

• applying heat shrinking tubes;

• shrink wrappers;

• thawing tubes and engines;

• repairing ﬁ nishing layers: email of bath and house-

hold appliances;

• applying epoxy powder cover layers;

• repairing of ski's, surf-boards and other sports goods;

• unscrewing too fast ﬁ xed screws and connections.

4. BEFORE OPERATING

Before you switch on the hot air gun you have to

search for the right adapter for the mouthpiece and as-

semble it on the mouthpiece if it is still cold.

IMPORTANT: Replace the mouthpiece only:

• with a stationary engine;

• when the appliance is disconnected;

• when the mouthpiece is cold.

5. OPERATION

• Check if the mains switch is on position “0” before

you connect the apparatus;

• Keep the power voltage always away from the hot air

stream and the mouthpiece.

Tip: If you want to get the best result, test all applian-

ces on a little part of the workpiece.

6. MAINTENANCE

Always disconnect the apparatus before carrying out

inspection or cleaning. Never use water or other li-

quids to clean the electrical parts of the hot air gun.

• Never use easy inﬂ ammable liquids for cleaning the

hot air gun, especially for the mouthpiece.

• Regular maintenance of your hot air gun prevents un-

necessary problems. Keep the ventilation slots of the

hot air gun clean to prevent overheating.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bort BHG-2000U-K Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info