Bedienungsanleitung Bort BS-300N (Seite 5 von 37) (Alle Sprachen)

555137

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

Finishing sander

INTENDED USE

This tool is intended for dry sanding and ﬁ nishing of

wood, painted surfaces, plastic and ﬁ ller

TECHNICAL SPECIFICATIONS 1

PRODUCT ELEMENTS 2

1 On/Off switch

2 Switch locking button

SAFETY

WARNING! Read all instructions. Failure to follow all

instructions listed below may result in electric shock,

ﬁ re and/or serious injury.

• Avoid damage that can be caused by screws, nails

and other elements in your workpiece; remove them

before you start working

• Always keep the cord away from moving parts of the

tool; direct the cord to the rear away from the tool

• When you put away the tool, switch off the motor

and ensure that all moving parts have come to a

complete standstill

• Use completely unrolled and safe extension cords

with a capacity of 16Amps (U.K. 13Amps)

• In case of electrical or mechanical malfunction,

immediately switch off the tool and disconnect the

plug

• SBM Group can assure ﬂ awless functioning of the

tool only when original accessories are used

• This tool should not be used by people under the

age of 16 years

• The noise level when working can exceed 85 dB(A);

wear ear protection

• If the cord is damaged or cut through while working,

do not touch the cord, but immediately disconnect

the plug

• Never use tool when cord is damaged; have it re-

placed by a qualiﬁ ed person

• Always check that the supply voltage is the same as

the voltage indicated on the nameplate of the tool

(tools with a rating of 230V or 240V can also be con-

nected to a 220V supply)

• This tool is not suitable for wet sanding

• Do not work materials containing asbestos (asbes-

tos is considered carcinogenic)

• When sanding metal, sparks are generated; do not

use dustbox and keep other persons and combusti-

ble material from work area

• Do not touch the moving sanding sheet

• Do not continue to use worn, torn or heavily clogged

sanding sheets

• Wear protective gloves, safety glasses, close-ﬁ tting

clothes and hair protection (for long hair)

• Take protective measures when during work dust

can develop that is harmful to one’s health, combus-

tible or explosive (some dusts are considered carci-

nogenic); wear a dust mask and work with dust/chip

extraction when connectable

• Always disconnect plug from power source before

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ON-

LY):

• Do not connect the blue (= neutral) or brown (= live)

wire in the cord of this tool to the earth terminal of

the plug

• If for any reason the old plug is cut off the cord of

this tool, it must be disposed of safely and not left

unattended

• the dust suction requires the use of perforated sand-

ing sheets

• perforation in sanding sheet should correspond with

perforation in sanding foot

• replace worn sanding sheets in time

• always use the tool with the total sanding surface

covered with sanding paper

• before the sanding surface reaches the workpiece,

you should switch on the tool

• before switching off the tool, you should lift it from

the workpiece

• do not apply too much pressure on the tool; let the

sanding surface do the work for you

Your machine is double insulated in accord-

ance with EN60745; therefore no earthwire is

required.

MAINTENANCE

Make sure that the machine is not live when

carrying out maintenance work on the motor.

Regularly clean the machine housing with a soft cloth,

preferably after each use. Keep the ventilation slots

free from dust and dirt.If the dirt does not come off use

a soft cloth moistened with soapy water. Never use

solvents such as petrol, alcohol, ammonia water, etc.

These solvents may damage the plastic parts.

The machine requires no additional lubrication.

Should a fault occur, e.g. after wear of a part, please

contact your local SBM Group dealer.

ENVIRONMENT

In order to prevent the machine from damage during

transport, it is delivered in a sturdy packaging. Most of

the packaging materials can be recycled. Take these

materials to the appropriate recycling locations. Take

your unwanted machines to your local SBM Group

dealer. Here they will be disposed of in an environmen-

tally safe way.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bort BS-300N Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info