Bedienungsanleitung Bosch 0 607 452 604 (Seite 19 von 126) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

97286

Zoom out

Zoom in

Vorherige Seite

1/126

Nächste Seite

English | 193 609 929 A78 • 8.8.06

Inserting

Press in the pin on the drive square of the bit holder 11,

e. g., with the aid of a small screwdriver, and slide the

tool bit 12 over the drive square. Take care that the pin

engages in the recess of the tool bit.

Removing

Press in the pin in the recess of the tool bit 12 and pull

the tool bit out of the tool holder 11.

Operating Instructions

Putting into Operation

The air tool operates optimally with a pressure of

6.3 bar (91 psi) measured at the air inlet with the tool

running.

f Pay attention to the direction of rotation that

is set before switching on the pneumatic tool.

For example, when a screw is to be loosened and

the direction of rotation is set so that the screw is

tightened, this can lead to a strong torque reaction

of the pneumatic tool.

Reversing the Rotational Direction

Right rotation: To screw in screws, turn the rotational

direction switch 9 in the given direction of the arrow to

the leftuntil it stops.

Left rotation: To loosen or to unscrew screws, turn

the rotational direction switch 9 in the given direction of

the arrow to the right until it stops.

f Operate the rotational direction switch 9 only

when the pneumatic tool is at a standstill.

Switching On and Off

Note: If the tool does not start after, for example, not

being used for a long period of time, disconnect the air

supply and turn the motor repeatedly by rotating the

tool bit holder 11. This eliminates adhesive forces.

The screwdriver have a shut-off clutch

that depends on the torque and can be set

in the given range. It responds when the

torque that is set is reached.

Switching on: Press the on/off switch 5 to the

stop.The screwdriver switches off automatically when

the adjusted torque setting is reached.

Switching off: Release the on/off switch 5.

f When the on/off switch 5 is released prema-

turely, the preset torque is not reached.

Working Instructions

f Disconnect the air hose from the air source

before making any adjustments, changing

accessories, or storing the pneumatic tool.

Such preventive safety measures reduce the risk of

starting the pneumatic tool accidentally.

f Place the tool bit onto the nut/screw only

when the screwdriver is switched off. Rotating

tool bits can slide off the nut/screw.

f In the event of an interruption of the air sup-

ply or reduced operating pressure, switch off

the pneumatic tool. Check the operating pres-

sure and restart the tool when the operating

pressure is again optimal.

Excess loads that cause the pneumatic tool to stall or

reduce speed will not damage the motor.

OBJ_BUCH-220-001.book Page 19 Tuesday, August 8, 2006 9:41 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch 0 607 452 604 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info