Bedienungsanleitung Bosch 230(J)B (Seite 15 von 261) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

119921

Zoom out

Zoom in

Vorherige Seite

1/261

Nächste Seite

English - 2

The numbering of the machine elements refers to

the representation of the machine on the graph-

ics page.

While reading the operating instructions, unfold

the graphics page for the machine and leave it

open.

1 Thread for auxiliary handle (3x)

2 Spindle lock button

3 On/Off switch

4 Auxiliary handle

5 Grinder spindle

6 Protection guard

7 Adjustment screw

8 Clamping lever

9 Mounting flange with O-ring

10 Grinding/cutting disc*

11 Clamping nut

12 quick-clamping nut*

13 Clamping screw

14 Coded projection

15 Guard, grinding cup*

16 Grinding cup*

17 Two-pin spanner for clamping nut*

18 Hand guard*

19 Spacer discs*

20 Rubber sanding plate*

21 Sanding sheet*

22 Round nut*

23 Cup brush*

24 Diamond cutting disc*

25 Cutting guide with dust extraction

protection guard*

26 Handle unlocking button

27 Handle

28 Cutting grinder stand*

* Not all of the accessories illustrated or described are

included as standard delivery.

Working safely with this machine

is possible only when the operat-

ing and safety information are

read completely and the instruc-

tions contained therein are

strictly followed. In addition, the

general safety notes in the enclosed booklet

must be observed. Before using for the first

time, ask for a practical demonstration.

■ Wear protective glasses and hearing protec-

tion.

■ Wear additional protection equipment for your

safety, such as protective gloves, sturdy

shoes, hard hat and apron.

■ The dust that is produced while working can be

detrimental to health, inflammable or explo-

sive. Suitable safety measures are required.

Examples: Some dusts are regarded as carci-

nogenic. Use suitable dust/chip extraction and

wear a dust respirator.

■ Dust from light alloys can burn or explode. Al-

ways keep the workplace clean, as blends of

materials are particularly dangerous.

■ If the mains cable is damaged or cut through

while working, do not touch the cable but im-

mediately pull the mains plug. Never use the

machine with a damaged cable.

■ Connect machines that are used in the open

via a residual current device (RCD) with an ac-

tuating current of 30 mA maximum. Do not op-

erate the machine in rain or moisture.

■ When working with the machine, always hold it

firmly with both hands and provide for a secure

stance.

■ Secure the workpiece. A workpiece clamped

with clamping devices or in a vice is held more

secure than by hand.

■ Always direct the cable to the rear away from

the machine.

■ Always switch the machine off and wait until it

has come to a standstill before placing it down.

■ For power outage or when the mains plug is

pulled, unlock the On/Off switch immediately

and turn it to the off position. This prevents un-

controlled restarting.

■ The machine must be used only for dry

cutting/grinding.

■ For all work with the machine, the auxiliary

handle must be mounted.

Machine Elements For Your Safety

1 609 929 R35.book Seite 2 Mittwoch, 13. Februar 2008 1:16 13

16 • 1 609 929 R35 • 03.11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch 230(J)B Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info