Bedienungsanleitung Bosch AdvancedDrill 18 (Seite 19 von 227) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

707735

Zoom out

Zoom in

Vorherige Seite

1/227

Nächste Seite

Fitting

Battery charging

u Use only the chargers listed on the accessories page.

Only these chargers are matched to the lithium-ion bat-

tery of your power tool.

Note: The battery is supplied partially charged. To ensure

full battery capacity, fully charge the battery in the charger

before using your power tool for the first time.

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by the "Electronic Cell Protection (ECP)". When the battery

is discharged, the power tool is switched off by means of a

protective circuit: The application tool no longer rotates.

u Do not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

Removing the battery

To remove the battery , press the battery release button and

pull the battery to the rear and out of the power tool. Do not

use force to do this.

Battery charge indicator

When the on/off switch (14) is pressed in halfway or com-

pletely, the battery charge-control indicator (13) indicates

the charge condition of the battery for several seconds. The

indicator consists of three green LEDs.

LED Capacity

Continuous lighting 3x green ≥ 66%

Continuous lighting 2x green 33–66%

Continuous lighting 1x green 11–33%

Slowly flashing light 1 x green ≤ 10%

The three LEDs in the battery charge indicator flash

quickly when the temperature of the battery is outside

the operating temperature range of –30 to +65 °C and/or

the overload protection has been triggered.

Changing the Tool

Inserting the application tool (seefigureA)

Insert the application tool all the way into the tool holder (2).

The application tool is held in the tool holder by means of a

magnet.

Removing

Remove the application tool from the tool holder (2).

Fitting the adapter (see figure B)

Remove the application tool.

Insert the adapter into the tool holder (2). The adapter clicks

audibly into place.

Check that it is seated securely by pulling the adapter.

Inserting the application tool into the adapter (see figure

Insert the application tool all the way into the adapter. The

application tool is held in the adapter by means of a magnet.

Screw holder (see figure D)

The screw holder (16) stabilises the screws so that they can

be better positioned on the workpiece.

Remove the application tool.

Push the screw holder onto the tool holder (2) until it aud-

ibly engages. Push the magnetic cap (15) as far as it will go

towards the power tool.

Then push the screwdriver bit (20) onto the screw holder

(16) and pull the magnetic cap forwards over the screw-

driver bit.

Push a screw onto the screwdriver bit.

Drill chuck adapter (see figure E)

Open the drill chuck adapter (18) by turning it in the direc-

tion of rotation  until the application tool can be inserted.

Insert the application tool.

Firmly tighten the sleeve of the drill chuck adapter (18) by

turning it by hand in the direction of rotation . This will

automatically lock the drill chuck.

Turning the adapter (see figure F)

Pull the unlocking ring (1) away from the power tool and

then pull the adapter off the tool holder (2).

Turn the adapter to the required position and then reattach

it.

Check that it is seated securely by pulling the adapter.

Removing the adapter (see figure G)

Remove the application tool.

Pull the unlocking ring (1) away from the power tool and

then pull the adapter off the tool holder (2).

Combining adapters (see figure H)

Remove the application tool.

Push the angle screw adapter (17) onto the tool holder (2).

Check that it is seated securely by pulling the angle screw

adapter (17).

Push the drill chuck adapter (18) onto the angle screw ad-

apter (17).

Check that it is seated securely by pulling the drill chuck ad-

apter (18).

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some

wood types, minerals and metal can be harmful to one’s

English | 19

Bosch Power Tools 1 609 92A 4BE | (07.09.2018)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch AdvancedDrill 18 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info