Bedienungsanleitung Bosch AdvancedRecip 18 (Seite 15 von 199) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

707754

Zoom out

Zoom in

Vorherige Seite

1/199

Nächste Seite

Selecting the saw blade

You will find an overview of recommended saw blades at the

end of these operating instructions. Only use saw blades

with a 1/2" universal shank. The saw blade should not be

longer than required for the intended cut.

The shank thickness of the saw blade has to be 0.8–1.6mm.

Inserting the saw blade (seefigure A)

Turn the locking sleeve(4) clockwise until the cam on the

locking sleeve is in a vertical position and pointing upwards,

and hold the locking sleeve firmly. Insert the saw blade(1)

into the saw blade receptacle. Turn the locking sleeve back

in an anticlockwise direction to lock the saw blade in place.

u Check that it is seated securely by pulling the saw

blade. A loose saw blade can fall out and lead to injuries.

For particular jobs, the saw blade(1) can also be flipped

180° (teeth point upwards) and refitted.

Removing the saw blade

u Let the saw blade cool down before removing it. There

is a risk of injury when touching the hot saw blade.

Turn the locking sleeve(4) clockwise until the cam on the

locking sleeve is in a vertical position and pointing upwards,

and hold the locking sleeve firmly. Remove the saw

blade(1). Turn the locking sleeve back in an anticlockwise

direction.

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some

wood types, minerals and metal can be harmful to one’s

health. Touching or breathing-in the dust can cause allergic

reactions and/or lead to respiratory infections of the user or

bystanders.

Certain dust, such as oak or beech dust, is considered carci-

nogenic, especially in connection with wood-treatment ad-

ditives (chromate, wood preservative). Materials containing

asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the ma-

terials to be worked.

u Avoid dust accumulation at the workplace. Dust can

easily ignite.

Operation

Start-up

Inserting the battery

u Use only original Bosch lithium-ion batteries with the

voltage stated on the type plate of your power tool.

Using other batteries can lead to injuries and pose a fire

hazard.

Note: The use of batteries unsuitable for your power tool can

lead to malfunctions or damage to the power tool.

Insert the charged battery(8) into the base of the power tool

until you feel it engage and it is securely locked in place.

Switching on/off

To switch on the power tool, press the lock-off switch (7)

first. Then press the on/off switch (6) and keep it pressed.

To switch off the power tool, release the on/off switch (6).

Note: For safety reasons, the on/off switch (6) cannot be

locked; it must remain pressed during the entire operation.

Controlling the stroke rate

You can variably adjust the stroke rate of the power tool

when it is on by pressing in the on/off switch (6) to varying

extents.

Applying light pressure to the on/off switch (6) results in a

low stroke rate. Applying increasing pressure to the switch

increases the stroke rate.

The required stroke rate is dependent on the material and

the work conditions and can be determined using practical

tests.

It is recommended that you reduce the stroke rate when

placing the saw blade on the workpiece and when sawing

plastic and aluminium.

During prolonged periods of use at a low stroke rate, the

power tool may heat up significantly. Remove the saw blade

and let the power tool run at the maximum stroke rate for

around three minutes to cool down.

Temperature-dependent overload protection

In normal conditions of use, the power tool cannot be over-

loaded. If the power tool is overloaded or the permitted bat-

tery temperature is exceeded, the electronics of the power

tool will switch off until the temperature returns to within the

optimum operating temperature range.

Practical advice

u Remove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

u Switch the power tool off immediately if the saw blade

becomes blocked.

Tips

u When sawing lightweight materials, take into account

the statutory provisions and recommendations of the

material manufacturers.

Before sawing into wood, chipboard, building materials,

etc., check for any foreign objects such as nails, screws, etc.

and use a suitable saw blade.

Switch on the power tool and guide it towards the workpiece

you wish to work on. Place the base plate(2) on the surface

of the workpiece and saw through the material applying even

pressure and feed. Switch the power tool off once you have

finished your work.

Switch the power tool off immediately if the saw blade jams.

Widen the sawing gap slightly with a suitable tool and pull

the power tool out.

English | 15

Bosch Power Tools 1 609 92A 4JX | (01.10.2018)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch AdvancedRecip 18 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info