Bedienungsanleitung Bosch AdvancedTableCut 52 (Seite 21 von 305) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

766874

Zoom out

Zoom in

Vorherige Seite

1/305

Nächste Seite

English | 21

uUse extra caution when making a cut into blind areas

of assembled workpieces. The protruding saw blade

may cut objects that can cause kickback.

uSupport large panels to minimise the risk of saw blade

pinching and kickback. Large panels tend to sag under

their own weight. Support(s) must be placed under all

portions of the panel overhanging the table top.

uUse extra caution when cutting a workpiece that is

twisted, knotted, warped or does not have a straight

edge to guide it with a mitre gauge or along the fence.

A warped, knotted, or twisted workpiece is unstable and

causes misalignment of the kerf with the saw blade, bind-

ing and kickback.

uNever cut more than one workpiece, stacked vertic-

ally or horizontally. The saw blade could pick up one or

more pieces and cause kickback.

uWhen restarting the saw with the saw blade in the

workpiece, centre the saw blade in the kerf so that the

saw teeth are not engaged in the material. If the saw

blade binds, it may lift up the workpiece and cause kick-

back when the saw is restarted.

uKeep saw blades clean, sharp, and with sufficient set.

Never use warped saw blades or saw blades with

cracked or broken teeth. Sharp and properly set saw

blades minimise binding, stalling and kickback.

Table saw operating procedure warnings

uTurn off the table saw and disconnect the power cord

when removing the table insert, changing the saw

blade or making adjustments to the riving knife or saw

blade guard, and when the machine is left unattended.

Precautionary measures will avoid accidents.

uNever leave the table saw running unattended. Turn it

off and don’t leave the tool until it comes to a com-

plete stop. An unattended running saw is an uncontrolled

hazard.

uLocate the table saw in a well-lit and level area where

you can maintain good footing and balance. It should

be installed in an area that provides enough room to

easily handle the size of your workpiece. Cramped,

dark areas, and uneven slippery floors invite accidents.

uFrequently clean and remove sawdust from under the

saw table and/or the dust collection device. Accumu-

lated sawdust is combustible and may self-ignite.

uThe table saw must be secured. A table saw that is not

properly secured may move or tip over.

uRemove tools, wood scraps, etc. from the table before

the table saw is turned on. Distraction or a potential jam

can be dangerous.

uNever stand on the table saw, do not use it as a step-

ping stool. Serious injury could occur if the tool is tipped

or if the cutting tool is accidentally contacted.

Additional safety information

uWhen mounting the saw blade, wear protective

gloves. This poses a risk of injury.

uDo not touch the saw blade after working before it has

cooled. The saw blade becomes very hot while working.

uKeep your work area clean. Material mixtures are partic-

ularly hazardous. Light metal dust may catch fire or ex-

plode.

uStore the power tool safely when it is not in use. The

storage location must be dry and lockable. This pre-

vents the power tool from storage damage, and from be-

ing operated by untrained persons.

uNever use the power tool if the cable is damaged. Do

not touch the damaged cable and pull out the mains

plug if the cable is damaged while working. Damaged

cables increase the risk of an electric shock.

uCheck the cable regularly and have a damaged cable

repaired only by an authorised customer service

agent for Bosch power tools. Replace damaged exten-

sion cables. This will ensure that the safety of the power

tool is maintained.

uDo not use the power tool for cutting slots (stopped

grooves).

uNever reach behind the saw blade to hold onto the

workpiece, remove wood chips or for any other

reason. The clearance between your hand and the rotat-

ing saw blade is too small when you do this.

uOperating as a saw: Guide the saw blade against the

workpiece only when the saw is switched on. Other-

wise there is a risk of kickback occurring if the saw blade

catches in the workpiece.

uOperation as a table saw: Only advance the workpiece

towards the saw blade when it is running. Otherwise

there is a risk of kickback occurring if the saw blade

catches in the workpiece.

uOperate the power tool only when the work area up to

the workpiece is clear of any adjusting tools, wood

chips, etc. Small pieces of wood or other objects that

come in contact with the rotating saw blade can strike the

operator with high speed.

uOnly saw one workpiece at a time. Workpieces placed

on top of or alongside each other can cause the saw blade

to jam or the workpieces to move out of place and against

each other when sawing.

uAlways use the universal guide. This improves the cut-

ting accuracy and reduces the possibility of the saw blade

jamming.

Products sold in GB only:

Your product is fitted with an BS 1363/A approved electric

plug with internal fuse (ASTA approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be

cut off and an appropriate plug fitted in its place by an au-

thorised customer service agent. The replacement plug

should have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible

shock hazard and should never be inserted into a mains

socket elsewhere.

Bosch Power Tools 1 609 92A 66E | (12.01.2021)

Bosch AdvancedTableCut 52 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info