Bedienungsanleitung Bosch AGS10-2 (Seite 15 von 28) (Englisch)

697423

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Commissioning | 15

6 720 811 270 (2015/04)AGS10-2, AGS10E-2, AGS20-2, AGS50-2

6.2.6 Determining the frost threshold temperature

To determine the degree of frost protection, we recommend checking

the frost protection of the heat transfer fluid when first putting the

system into operation, by means of a frost protection gauge (a

refractometer). This check should be repeated at regular intervals (at

least every two years).

The commonly used instruments for testing motor vehicle engine

coolants are not suitable for this purpose. A suitable device can be

ordered separately.

For system operation with heat transfer medium LS

If the solar system is operated with heat transfer medium LS, the value

must be converted using Tab. 10.

6.2.7 Correcting frost protection

If the minimum frost protection level is not being maintained, more heat

transfer fluid must be added.

▶ Use Tab. 11 to determine the volume of the system, so that you can

calculate the exact amount to be added (which is equal to the amount

which first needs to be drained out).

▶ Use the formula on the right to determine the amount of concentrate

to be added (V

replace

Example of heat transfer medium L:

• System volume (V

total

) = 22 l

• Frost protection level (reading taken): – 14 °C

• Equals concentration of ( Tab. 10, page 15): 29 % (C = 29)

•Result: V

replace

= 4.3 l

▶ Drain the calculated amount to be added (V

replace

) and add

concentrate.

6.3 Setting the flow rate

The flow rate is set when the system is cold (30 - 40 °C).

• When the solar pump is speed-controlled, the controller determines

the flow rate based on operating requirements.

• If the controller is not equipped with speed control or if speed control

has been deactivated, the flow rate must be set to a fixed flow rate.

If you wish to set the flow rate:

1. Carry out the preparatory work ( Chapter 6.3.1)

2. Check the flow rate ( Chapter 6.3.2)

3. Set the flow rate ( Chapter 6.3.3)

6.3.1 Carrying out the preparatory work

▶ Rotate ball valves [1] to 0° (check valves ready for operation).

▶ Completely open the flow limiter [2].

▶ On the controller, select mode “Manual ON” ( controller instruction

manual).

Fig. 26

[1] Gravity brake ready for operation

[2] Adjusting screw on the flow limiter, depending on the type

[3] Read-off edge for the flow rate, depending on the type

Value recorded for heat transfer

medium L (concentration)

Corresponds to frost protection

with heat transfer medium LS

– 23 °C (39 %) – 28 °C

– 20 °C (36 %) – 25 °C

– 18 °C (34 %) – 23 °C

– 16 °C (31 %) – 21 °C

– 14 °C (29 %) – 19 °C

– 11 °C (24 %) – 16 °C

– 10 °C (23 %) – 15 °C

– 8 °C (19 %) – 13 °C

– 6 °C (15 %) – 11 °C

– 5 °C (13 %) – 10 °C

– 3 °C (8 %) – 8 °C

Table 10

NOTICE: Frost damage

▶ Every two years, check whether the required frost

protection level (to at least –25 °C) is being

maintained.

System part Fill volume

Collector: see collector instructions (technical data)

1 single-line solar pump station 0.20 l

1 twin-line solar pump station 0.50 l

1 coil in the solar cylinder (see technical guide)

1 m Cu pipe Ø 15 mm 0.13 l

1 m Cu pipe Ø 22 mm 0.31 l

1 m Cu pipe Ø 28 mm 0.53 l

1 m Cu pipe Ø 35 mm 0.86 l

1 m Cu pipe Ø 42 mm 1.26 l

1 m stainless steel corrugated pipe DN16 0.26 l

1 m stainless steel corrugated pipe DN20 0.41 l

1 m stainless steel corrugated pipe DN25 0.61 l

Table 11 Volume of the separate system parts

replace

= V

total

43 - C

concentration

100 - C

concentration

Table 12 Formula for calculating the amount of fluid to be replaced

0,5

L/min

0,5

6720801165.18-2.ST

°C

100

120

°C

100

120

S E

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch AGS10-2 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info