Bedienungsanleitung Bosch AHS 55-24S (Seite 11 von 69) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

473368

Zoom out

Zoom in

Vorherige Seite

1/69

Nächste Seite

English - 3

Electrical Safety

Your machine is double insulated for safety and re-

quires no earth connection. The operating voltage is

230 V AC, 50 Hz. Only use approved extension ca-

bles. Contact your service agent for details.

Extension cords/leads should only be used if they

comply with H05VV-F or H05RN-F types.

It is recommended for increased electrical safety to

use a Residual Current Device (RCD) with a tripping

current of not more than 30 mA. Always check your

RCD every time you use it.

For products not sold in GB: WARNING: For

safety, it is essential that the mains plug 6 attached

to the machine is fitted to the power supply cable 8

as shown.

The couplings of connection leads must be pro-

tected against splashes and the coupling sockets on

the leads must be made of rubber or coated with

rubber.

Fixing means for the connection leads must be

used.

The connection lead must be inspected for signs of

damage at regular intervals and may only be used if

in perfect condition.

If the supply cord is damaged, it must be replaced by

a Bosch approved Service Agent.

Products sold in GB only: Your hedecutter is fitted

with an approved 13 A (BS 1363/A) electric plug and

is protected by a 13 A fuse (ASTA Approved to

BS 1362).

If the fitted plug is not suitable for your socket out-

lets, it should be cut off and an appropriate plug fit-

ted in its place.

The severed plug must be disposed of to avoid a

possible shock hazard and should never be inserted

into a 13 A socket elsewhere.

Starting:

Press and hold rear switch lever 5. Squeeze any

front lever 3.

Stopping:

Release any of switch levers 3 and 5.

Hold the hedgecutter away from yourself

using both hands. Stand in a secure and

stable position.

Position the extension cord over your shoulder to the

rear and ensure that the cord is behind you at all

times during cutting. Never place the cable over the

hedge, where it could easily be cut by the blades.

Cut stems upto 24 mm in thickness. When cutting,

move steadily along the line of cut, so that stems are

fed directly into the cutter blades. The double edge

of the cutting blade enables cutting to either direc-

tion, or with a side to side motion.

Cut the sides of the hedge first, then the top.

To keep the sides flat, cutting upwards with the

growth is recommended. Younger stems tend to

move outwards when cutting them from top to bot-

tom, resulting in shallow patches or holes in the

hedge.

To reach a level finish, fasten a piece of string along

the length of the hedge at the required height and

use as an alignment guide. Cut the hedge just above

the string.

Take care to avoid cutting into objects such as wire,

which could cause damage to the cutting blades and

the drive.

Recommended cutting/trimming times:

– Cut hedges with deciduous leaves in June and

October.

– Cut evergreen hedges in April and August.

– Cut conifer and other fast growing shrubs approx.

every six weeks from May onwards.

– Shaping hedges should be cut to achieve a form

as shown in figure.

Prior to any maintenance remove plug

from power supply.

Note: To ensure long and reliable service, carry out

the following maintenance regularly.

Check for obvious defects such as loose, dislodged

or damaged blade, loose fixings and worn or dam-

aged components.

Check that covers and guards are undamaged and

correctly fitted. Carry out necessary maintenance or

repairs before using.

For Your Safety

WARNING! SWITCH OFF, REMOVE PLUG

FROM MAINS BEFORE ADJUSTING, CLEAN-

ING OR IF CABLE IS CUT, DAMAGED OR EN-

TANGLED.

THE BLADES CONTINUE TO MOVE FOR A

FEW FRACTIONS OF A SECONDS AFTER THE

HEDGECUTTER IS SWITCHED OFF. CAU-

TION! DO NOT TOUCH THE MOVING BLADES.

Starting and Stopping

Tips on Cutting

Maintenance

B C D

11 • 2 609 932 122 • 08.01

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch AHS 55-24S Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info