78524
24
Zoom out
Zoom in
Vorherige Seite
1/159
Nächste Seite
English - 7
24 F016 L70 360 TMS 11.07.06
Particular attention must be given when sawing
sidewards, slanted or during length cuts, as the grip-
ping teeth 12 usually can not be applied.
To avoid kickback:
Saw with the chain bar at a flat angle.
Never work with a loose, widely stretched or the
heavily worn out chain.
Ensure chain is sharpened correctly.
Never saw above shoulder height.
Never work with the tip of the chain bar.
Always the hold chain saw firmly with both hands.
Always use a Bosch low-kickback chain.
Apply the metal gripping teeth 12 for leverage.
Ensure correct chain tension.
General Behaviour
Always hold the chain saw firmly with both
hands. Front grip with the left hand and rear grip with
the right hand. Fully grip both handles at all times
during operation. Never operate chain saw using
only one hand. Ensure power cord is located to the
rear, away from the chain and wood and so pos-
tioned that it will not be caught on branches or the
like during cutting.
Use the chain saw only with secure footing. Hold
the chain saw at the right-hand side of your body.
The chain must be running at full speed before it
makes contact with the wood. Use the metal grip-
ping teeth 12 to secure the saw onto the wood be-
fore starting to cut. Use the gripping teeth as a lev-
erage point X while cutting.
Reset the gripping teeth at a lower point when saw-
ing thicker logs by pulling the chain saw slightly
backwards until the gripping teeth release, and repo-
sition at lower level to continue sawing. Do not re-
move the saw completely from the wood.
Do not force the chain while cutting, let the chain do
the work, using the gripping teeth 12 to apply mini-
mal leverage pressure.
Do not operate the chain saw with arms fully ex-
tended or attempt to saw areas which are difficult to
reach, or on a ladder. Never use the chain saw
above shoulder height.
Sawing is optimized when the chain speed remains
steady during cutting.
Beware when reaching the end of the cut. The
weight of the saw may change unexpectedly as it
cuts free from the wood. Accidents can occur to the
legs and feet.
Always remove the saw from a wood cut while the
saw is running.
Cutting Logs
Observe the following safety instructions:
Support logs so that the face sides at the cut
do not close in against each other, which would re-
sult in the chain being jammed or pinched.
Position and set short logs safely prior to sawing.
Saw only wood or wooden objects. When sawing, al-
ways take care to avoid hitting stones, nails, etc., as
these could be thrown up or cause damage to the
chain or serious injury to the operator or bystanders.
Keep a running saw clear of wire fencing or the
ground.
Use of the saw to thin out branches or bushes is not
approved.
Length cuts must be carried out with care, as lever-
age with the gripping teeth 12 is not possible. Saw at
a flat angle to avoid kickback.
When working on a slope, operate above or to the
side of the trunk or laying tree.
Be careful not to trip over tree stumps, branches,
roots, etc.
Cutting Wood under Tension
There is a high risk of accidents when sawing wood,
branch or trees under tension. Be extremely careful.
Leave saw jobs like these to professionals.
When sawing logs supported on both ends, start the
cut from above (Y) about 1/3 of the diameter into the
log and then finish the cut (Z) from below, in order to
avoid splitting of the log or jamming of the saw.
Avoid contact of the chain saw with the ground.
When sawing logs supported on only one end, start
the cut from below (Y) about 1/3 of the diameter into
the log and finish the cut from above (Z), in order to
avoid log splitting or jamming of the chain saw.
Felling Trees
Always wear hard hat to protect head
against falling branches.
The chain saw can only be used to fell trees
smaller in diameter than the length of the chain
bar.
Secure work area. Ensure no persons or ani-
mals are in the vicinity of the falling tree.
Never attempt to free a jammed saw with the mo-
tor running. Use wooden wedges to free chain
and chain bar.
When cutting and felling operations are being per-
formed by two or more persons, at the same time,
the felling operations should be separated from the
cutting operation by a distance of at least twice the
height of the tree being felled. Trees should not be
felled in a manner that would endanger any person,
strike any utility line or cause any property damage.
If the tree does make contact with any utility line, the
company should be notified immediately.
D
E
F
G
E H
H
I
F016 L70 360 - GB Seite 7 Dienstag, 18. Juli 2006 9:20 09
24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

bosch-ake-40-18s

Suche zurücksetzen

  • bosch40-18s, zum Reinigen möchte ich den Deckel abnehmrn - habe schon mehrmals gemacht- plötzlich geht es nicht mehr, beim Drehen des Drehdeckels passiert nichts, er dreht nur durch, man kann aber den Deckel nicht abnehmen. Danke voraus für die Antwort. Eingereicht am 26-6-2020 17:45

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch AKE 40-18S wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info