Bedienungsanleitung Bosch AKE 40-19S (Seite 22 von 153) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

105962

Zoom out

Zoom in

Vorherige Seite

1/153

Nächste Seite

English - 22

22 • F016 L70 506 • TMS • 19.10.07

Important: The chain saw is not supplied

filled with oil. It is essential to fill with oil

before use. Never operate the chain saw

without chain oil or at an empty oil tank level, as

this will result in extensive damage to the prod-

uct.

Chain life and cutting capacity depend on optimum

lubrication. Therefore, the chain is automatically

oiled during operation via the oil outlet 19.

Filling oil tank:

– Set chain saw on any suitable surface with oil filler

cap 4 facing upward.

– Clean area around the oil filler cap 4 with cloth,

unscrew cap.

– Do not remove filter insert during filling.

– Add Bosch biodegradable chain saw oil until res-

ervoir is full.

– Avoid dirt or debris entering oil tank, refit oil filler

cap 4 and tighten.

Important: To allow venting of the oil res-

ervoir,small breather channels are pro-

vided between the oil filler cap and the

strainer, to prevent leakage ensure machine is

left in a horizontal position (oil filler cap 4 upper-

most) when not in use.

It is important to use only the recommended bi-

odegradable oil to avoid damage to the chain

saw. Never use recycled/old oil. Use of non ap-

proved oil will invalidate the warranty.

Observe the correct mains voltage! The voltage

of the power source must agree with the value given

on the nameplate of the machine. Machines desig-

nated for 230 V can also be operated with 220 V.

Switching On and Off

Hold chain saw as described in “Cutting”.

For switching on the machine, press the lock-off

button 3, then fully press the On/Off switch 2 and

hold in this position. The lock-off button 3 can now

be released.

For switching off, release the On/Off switch 2.

Do not stop chain saw after sawing by activating

the front hand guard (kickback brake).

The chain saw is equipped with two chain brake sys-

tems for user safety:

The run down brake automatically stops the chain

and motor after the switch lever (On/Off) 2 is re-

leased.

The kickback brake is a safety mechanism acti-

vated through the front hand guard 5, when kickback

occurs. Chain stops immediately.

The following function check should be carried out at

regular intervals. Push front hand guard 5 forward

(position ➋) that the red marker 28 under indicator 6

is visible and start the chain saw. The chain must not

start. To deactivate the kickback brake, pull hand

guard 5 backwards (position ➊) that the red

marker 28 under the indicator 6 is covered (see fig-

ure ).

Before Cutting

Before and periodically during cutting check as fol-

lows:

– Is the chain saw in a fail-safe condition?

– Is the oil reservoir filled? Check oil level

gauge 26 prior to starting and regularly during op-

eration. Refill oil when oil level is low. The oil tank

filling will last approx. 15 minutes, depending on

sawing intensity and stops.

– Is the chain tension in order and is the chain

sharp? Check chain tension every 10 minutes

during operation. Upon initial operation, new

chains can lengthen considerably. The condition

of the chain influences the the cutting perform-

ance. Only a sharp chain protects from overload.

– Is the kickback brake deactivated and its function

ensured?

– Are you wearing the necessary protective equip-

ment? Wear safety glasses and hearing protec-

tion. Further protective equipment for head, hand,

legs and feet is recommend. Adequate protective

clothing will reduce personal injury by flying de-

bris or accidental contact with saw chain.

Kickback

Kickback is the sudden backward/upward motion of

the chain saw, occuring when the chain (at the tip of

the chain bar) comes in contact with a log or wood,

or when the chain becomes jammed.

When kickback occurs the chainsaw reacts unpred-

icably and can cause severe injuries to the operator

or bystanders.

Lubrication

Starting and Stopping

A B

Kickback Brake/

Run Down Brake

Cutting

F016 L70 506 - GB Seite 22 Dienstag, 23. Oktober 2007 3:20 15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch AKE 40-19S Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch AKE 40-19S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info