Bedienungsanleitung Bosch AMAX panel 4000 EN (Seite 26 von 170) (Englisch)

697454

Zoom out

Zoom in

Vorherige Seite

1/170

Nächste Seite

26 en | Installation AMAX panel

2019.08 | 11 | F.01U.309.277 Installation Manual Bosch Security Systems B.V.

5.4 System status indicator

The AMAX panel indicates the system status by using the LED status indicator on the system

main board.

Slow flash of red on status indicator (repeating on and off with an interval of one second)

indicates a normal system operation.

5.5 Certification

Prerequisites for certification conform installation

The AMAX panel is certified. To realize a usage of the system conformable to the certification

described in this chapter, the following prerequisites have to be fulfilled:

– Use one of the following possibilities for devices:

– Two supervised warning devices (PO-1 PO-2 & PO+) and one ATS 2 communicator

(onboard dialer, B426-M or D4020)

– One self powered warning device and one ATS 2 communicator (onboard dialer,

B426-M or D4020)

– Two communicators, one ATS 2 (onboard dialer, B426-M or D4020) and one ATS 1

(onboard dialer, B426-M or D4020)

– One ATS 3 communicator (DX4020 or B426-M)

– Connect all communicators to a central monitoring station.

– Only use the onboard dialer and the option bus communicator for alarm transmission.

– Connect one 12V / 7AH or one 12V / 18Ah battery to the system.

– Ensure the maximum current for all components with a 7Ah Battery to be 550mA.

– Ensure the maximum current for all components with a 18Ah Battery to be 1500mA

(standby 12h, recharge battery 80% in 72h) (PCB =l 00mA, IUI-AMAX Keypads = 31mA,

DX2010 = 35mA, DX3010 = 10mA, B426-M = 100mA, B450-M = 180mA, RF3227E = 30mA,

RFRC-OPT = 30mA).

– Make sure to have an indication of the arm / disarm status accessible from outside the

monitored area (this indication has to be time limited).

– Use one of the following methods for the access to the monitored area:

– Starting the entry procedure by opening a door

– Indicating the arm / disarm status

– Preventing the access to the monitored area (e.g. mechanical door strike)

– Only use the enclosure lock only in non EN setup.

– Only use the telephone arming in non EN setup.

– Only mount additional modules (except input module DX2010) inside the enclosure.

– If one or more communicator modules are mounted in an extra enclosure, this enclosure

must have a tamper protection.

– Install the tamper skirt on the PCB of the input module DX2010, if the input module

DX2010 is mounted on the external enclosure (AE20).

– Program the system with the EN settings indicated on the programming sheet.

– Remove the EN indication (on label) if the system is set without EN parameters.

– Connect no more than 10 devices to one zone input (Panel, Keypad, Input Module, RFUN,

…)

– For an EN50136-1, -2 SP4 compliant installation, select the transmission format "SIA

DC09 (2x ID)".

5.5.1 EN 50131-3 Grade 2, Environmental Class 2 - AMAX 2100 / 3000 / 3000

BE / 4000

Certification Body:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch AMAX panel 4000 EN Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch AMAX panel 4000 EN

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info