Bedienungsanleitung Bosch AMAX panel 4000 EN (Seite 30 von 170) (Englisch)

697454

Zoom out

Zoom in

Vorherige Seite

1/170

Nächste Seite

30 en | Settings AMAX panel

2019.08 | 11 | F.01U.309.277 Installation Manual Bosch Security Systems B.V.

6 Settings

This chapter describes the settings of the AMAX panel in the same order as they appear in the

menu structure of the text keypad. For an overview of the menu structure, refer to Text keypad

programming, page 94.

The settings can be configured either via a text keypad or via the PC software A-Link Plus.

For information on how to configure the settings via a text keypad and how to navigate a text

keypad, refer to Text keypad programming, page 94.

For information on how to connect the AMAX panel to a PC, refer to Communication with PC

software, page 105.

6.1 Communication and reporting

This section outlines the programming information required for the AMAX panel when

communicating with a base station receiver. These parameters specify the telephone

numbers/IP address to be called, transmission formats, and internet communication options.

6.1.1 Receivers

Receiver telephone number / IP address and port

The AMAX panel can report event information from an on-board dialer, which can call four

different receivers and four different telephone numbers. The dialer reports to receiver 1 to 4

by programming. You can program the dialer with 4 separate telephone numbers/IP addresses

and ports, reporting format type and subscriber ID number, and internet communication

options if necessary.

Example

You can set up dialer 1 to report to receiver 1 in Bosch Network (Conettix) format and set up

dialer 2, dialer 3, and dialer 4 to report to a receiver of a central monitoring station in Contact

ID format only, if dialer 1 is unsuccessful.

How to program a telephone number via a text keypad

1. Enter the digits of a telephone number in the text keypad.

2. To enter a 4-sec pause in the dialing sequence, enter [*] [3].

A pause might be necessary when the dialer communicates through an old (slower)

telephone exchange or when a PABX system is in place.

How to program a telephone number via address programming

1. Enter one digit of a telephone number in each address for the telephone numbers.

2. To enter a 4-sec pause in the dialing sequence, insert “13”.

A pause might be necessary when the dialer communicates through an old (slower)

telephone exchange or when a PABX system is in place.

3. To terminate the input, insert “15”.

Example for address programming

– To program the telephone number “9672 1055” as the telephone number for receiver 1,

program the following sequence into address 000 - 016:

[9 6 7 2 1 0 5 5 15 x x x x x x x x] (x stands for any digit)

– To program the number “02 pause 9672 1055”, program the following sequence into

address 000 - 016:

[0 2 13 9 6 7 2 1 0 5 5 15 x x x x x]

The following table shows how to program the numbers, keys, and functions for a telephone

number via address programming or via installer menu programming.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch AMAX panel 4000 EN Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch AMAX panel 4000 EN

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info