697454
43
Zoom out
Zoom in
Vorherige Seite
1/170
Nächste Seite
AMAX panel Settings | en 43
Bosch Security Systems B.V. Installation Manual 2019.08 | 11 | F.01U.309.277
6.1.3 Test report duration
There are two types of automatic test reports, configurable periodic reports and regular daily
reports. The periodic test is sent according to the configuration (interval, hour and minute)
and the local time. Therefore, the date and time of the system has to be set correctly. When
the time that is configured as hour and minute is reached, a periodic test report is sent. The
next periodic test report is sent after the configured interval and is not influenced by any
other reports sent in between periodic test reports.
Test report interval
The test report interval can be set to 1 hour, 2 hours, 3 hours, 4 hours, 6 hours, 8 hours, 12
hours or 24 hours.
The periodic test report can be disabled. Regular daily automatic test reports will be sent
instead.
Test report hour
In this option the reference hour from which the test report interval will be started can be
entered. Values from 00 - 23 are valid. An invalid value will be treated as 00.
Test report minute
In this option the reference minute from which the test report interval will be started can be
entered. Values from 00 - 59 are valid. An invalid value will be treated as 00.
6.1.4 Dual IP
Dual IP Settings are valid only when used with Conettix IP communication format. For IP
module 1 and 2, B426-M module are used. IP module 2 does not support RPC connection.
When the report is transmitted with Conettix IP communication, some reports might be
missed.
The communication path of B426-M module / B450-M module is as follows:
Module Address Setting Corresponding
Communication Path
Module 1: B426-M module 1 /
B450-M
134 Paths 1 and 2
Module 2: B426-M module 2 250 Paths 3 and 4
Only when IP module 1 is used and set to paths 1 to 4, the report can be sent to those paths.
6.1.5 IP communicator
Modules
The modules B426-M and B450-M can be connected to the AMAX panel and used as IP
communicators.
B426-M can be set as module 1 or 2. B450-M can only be set as module 1.
For more information on B426-M and B450-M, refer to the corresponding manuals.
IPv6 mode
This option enables / disables the IPv6 mode. If this option is disabled, the IPv4 mode is used.
IPv4 DHCP
This option enables / disables the IPv4 DHCP. If a DHCP service is available is this option is
enabled, the IPv4 address, the IPv4 subnet mask, the IPv4 default gateway, the IPv4 DNS
server IP and alternative IPv4 DNS server IP are configured automatically.
IPv4 address
This option sets the IPv4 address. Possible values are 0.0.0.0 to 255.255.255.255.
43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch AMAX panel 4000 EN wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Bosch AMAX panel 4000 EN

Bosch AMAX panel 4000 EN Kurzanleitung - Deutsch - 76 seiten

Bosch AMAX panel 4000 EN Kurzanleitung - Holländisch - 76 seiten

Bosch AMAX panel 4000 EN Installationsanweisung - Holländisch - 190 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info