697454
70
Zoom out
Zoom in
Vorherige Seite
1/170
Nächste Seite
70 en | Settings AMAX panel
2019.08 | 11 | F.01U.309.277 Installation Manual Bosch Security Systems B.V.
Zone lockout
The zone lockout defines after how many times of triggering an alarm during one arming cycle,
the zone in which the alarm occurred will be “locked”. If a zone is locked, the alarms its
alarms will be ignored by the system. This option defines whether the zone lockout mode is
allowed for a zone and after how many times of triggering an alarm the zone will be locked.
The following selections are possible:
Disabled
Locked after triggering the alarm 1 time
Locked after triggering the alarm 3 times
Locked after triggering the alarm 6 times
Alarm duration
The zone lockout will be reset after disarming.
1 time
The AMAX panel will process locking according to the following logic:
1. When an alarm is triggered within the period of alarm output time, the AMAX panel will
ignore the status detection of the zone.
2. After the alarm has been triggered 1 time, the zone will be locked.
3. If the alarm occurs in the locked zone, the zone will send zone fault report.
4. Before the end of the alarm output time, ten zone recovery events will not be transmitted.
5. If the zone locking option is disabled, the times of alarms will not be restrained. Even
when other zones are locked, that zone can still generate the alarm.
3 times
Similar to 1 time of alarm locking, with alarm limited to not more than 3 times.
6 times
Similar to 3 times of alarm locking, with alarm limited to not more than 6 times.
Alarm duration
Locking occurs within the period of alarm output time. Repeating the process of alarm locking
in the period of alarm output time, without limit to times.
Zone EOL
The system supports tamper detection of the zone. This function ensures that the zone is in
normal operating status and triggers an alarm if not. The following selections are possible:
0 = EOL 2,2k
1 = DEOL 2,2k / 2,2k
2 = reserved
3 = NC
4 = NO
EOL 2,2k (end of line)
An EOL resistor with 2,2k is required for the zone. A zone alarm is triggered if another value
than 2,2k is registered.
DEOL 2,2k / 2,2k (double end of line)
A DEOL resistor with twice 2,2k is required for the zone. A zone alarm is triggered if 4,4k are
registered. A tamper alarm is triggered if any other value is registered.
NC (normally closed)
A NC resistor is required for the zone. A zone alarm is triggered if the resistor is opened.
NO (normally open)
A NO resistor is required for the zone. A zone alarm is triggered if the resistor is closed.
70

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch AMAX panel 4000 EN wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Bosch AMAX panel 4000 EN

Bosch AMAX panel 4000 EN Kurzanleitung - Deutsch - 76 seiten

Bosch AMAX panel 4000 EN Kurzanleitung - Holländisch - 76 seiten

Bosch AMAX panel 4000 EN Installationsanweisung - Holländisch - 190 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info