382378
22
Zoom out
Zoom in
Vorherige Seite
1/130
Nächste Seite
22 | English
F 016 L70 546 | (13.1.11) Bosch Power Tools
Autostop function
The machine is designed to switch off the motor
when the trigger 9 is released on the gun. This
feature relieves high pressure from the system
to achieve a longer lifetime and lower energy
consumption. (A short squeaking noise can oc-
cur and is completely normal.)
Stopping
Release trigger 9. Press the trigger safety lock
10. The power gun is now locked and can not be
operated accidentally.
Press on/off switch 4.
Close water tap. Unplug the machine from the
mains supply.
Press the trigger safety lock 10 to release the
trigger 9. Fully press the trigger 9 until there is
no more water pressure in the machine. Release
trigger 9. Press the trigger safety lock 10.
Disconnect water supply hose from machine
and water supply.
Self priming function
The machine can also operate with water from
sources other than a water tap, e. g. ponds and
water butts due to the self priming function. The
use of an additional water filter (not supplied)
is highly recommended for this kind of use.
Make sure the water source is situated no more
than 1 m below the level of the machine.
Fill water supply hose (not supplied) with water
before connecting it to the machine. Running
the machine without water (running dry) will
damage it.
Run machine without lance attached until there
is a constant flow of water.
Turn off machine and connect lance.
Working Advice
General
Ensure that the pressure washer is on level
ground.
Do not kink or drive a motor vehicle over the
high pressure hose. Do not expose the high
pressure hose to sharp edges or corners.
Never use the roto jet mode to clean motor vehi-
cles.
Troubleshooting
The following chart lists problem symptoms, possible causes and corrective action, if your pressure
washer does not operate properly. If these do not identify and correct the problem, contact your
service agent.
f Warning: Switch off and remove plug from mains before investigating fault.
Problem Possible Cause Corrective Action
Motor refuses to start Plug not connected Connect plug
Mains socket faulty Use another socket
Fuse faulty/blown Replace fuse
Extension cable damaged Try without extension cable
Motor stops Fuse faulty/blown Replace fuse
Wrong mains voltage Check that mains voltage corre-
sponds to specifications on the
model tag
OBJ_BUCH-764-002.book Page 22 Thursday, January 13, 2011 3:33 PM
22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch aquatak clic 135 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info