Bedienungsanleitung Bosch ARM 320 (Seite 14 von 84) (Alle Sprachen)

632161

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

EURO • Printed in England • BA F 016 L69 797 • ARM 320 • GB • OSW 11/00

English - 3

F016 L69 797 • 11.00

Electrical Safety

Your machine is double insulated for safety and re-

quires no earth connection. The operating voltage is

230 V AC, 50 Hz. Only use an approved extension

cable. Contact your service agent for details.

It is recommended for increased electrical safety to

use a Residual Current Device (RCD) with a tripping

current of not more than 30 mA. Always check your

RCD every time you use it.

WARNING: For safety, it is essential that the mains

plug 4 attached to the machine is fitted to the power

supply cable 11 as in figure B.

The couplings of connection leads must be protected

against splashes and the coupling sockets on the

leads must be made of rubber or coated with rubber.

Fixing means for the connection leads must be used.

The connection lead must be inspected for signs of

damage at regular intervals and may only be used if

in perfect condition.

If the supply cord is damaged it must be replaced by

a Bosch approved service agent.

Extension cords/leads should only be used if they

comply with H05VV-F or H05RN-F types.

Products sold in GB only: Your mower is fitted with

an approved 13 A (BS 1363/A) electric plug and is

protected by a 13 A fuse (ASTA Approved to

BS 1362).

If the fitted plug is not suitable for your socket outlets,

it should be cut off and an appropriate plug fitted in

its place.

The severed plug must be disposed of to avoid a

possible shock hazard and should never be inserted

into a 13 A socket elsewhere.

➊

Insert the handle bottom 8 into the holes pro-

vided and

➋

secure with the screws.

➌

Attach the handle top 3 with the bolts and wing

nuts 12 to the handle bottom 8, as in figure A.

Note: The handle top 3 is height adjustable. Fix han-

dles in desired position I or II.

Attach cable to cable restraint 5 as in figure B ensur-

ing that sufficent cable slack is available.

Snap together both top and bottom half of the grass-

box.

Fitting

Lift the deflector guard 7 and hold up, fit the grass-

box 6.

Removing/Emptying

Lift the deflector guard 7 and hold up. Remove

grassbox 6.

For non grass collection the mower can be used

without the grassbox 6 in position, with the deflector

guard 7 in the down position.

Stop, release switch lever and wait until

the motor stops before adjusting hight.

Your machine has four settings which give the fol-

lowing approximate height of cuts:

I = 24 mm II = 40 mm III = 55 mm IIII = 70 mm

Remove the grassbox to aid adjustment (see Grass-

box).

Lift the mower,

➊

Pull/push the wheel to the front of the mower us-

ing the hand positioned on the wheels.

➋

Raise/lower the wheel.

➌

Allow wheel to locate in desired position as in fig-

ure D.

Make sure that all wheels are set to the same height.

For the first cutting of the season, a high cutting ad-

justment should be selected.

Assembly

Grassbox

Adjusting the Cutting Height

F 016 L69 797.book Seite 3 Dienstag, 21. November 2000 7:52 07

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch ARM 320 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info