Bedienungsanleitung Bosch ART 23 GSA (Seite 16 von 97) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

537972

Zoom out

Zoom in

Vorherige Seite

1/97

Nächste Seite

English - 4

EURO • Printed in England • BA F 016 L69 858 • ART 23/25 • GB • OSW 07/01

For increased access move adjustable handles 4 to

position III see figure E2.

(Model ART 23 GFS/GFSV)

(Model ART 25 GSA/GSAV)

Trimming Edges

(Model ART 23 GFSV/ART 25 GSAV/ART 25

ERGOPOWER)

Run the trimmer along the edge of the lawn as shown

in figure F. Do not allow the cutting line to contact

paved surfaces or garden walls, since this will wear

the line rapidly.

Trimming Edges (ART 23 GFS/ART 25 GSA)

Use handle position IV for edging.

Cutting Around Trees and Bushes

Carefully cut around trees and bushes so that they

do not come into contact with the cutting line.

Plants can die if you damage the bark.

For better control use guide handle 3 or adjustable

handle 4.

The rotating line can wear or break. You will notice

when the motor runs without load and no grass is cut.

Model ART 23 G

Switch off the machine and remove plug

from the mains.

The line must be fed manually:

Hold the spool plate 14 in position, lift the line up and

pull it out approx. 9 cm counter-clockwise. Clasp the

line between the studs of the spool plate as shown in

figure G.

If the line is exceeding the maximum cutting circle it

will be cut by the blade 15 integrated in the cutting

guard 8.

Model ART 23 GF/GFS/GFSV

While operating the trimmer press and release the

trimmer firmly against a solid base such as a pave-

ment surface as shown in figure G2 (necessary pres-

sure approx. 3 kg). The spool will release approx.

4 cm of line per action.

When the line breaks off completely feed twice to re-

gain the full cutting circle.

If the line is exceeding the maximum cutting circle it

will be cut by the blade 15 integrated in the cutting

guard 8.

Model ART 25 GSA/GSAV/ERGOPOWER

While operating the trimmer the line will be fed auto-

matically when it breaks.

Stop and remove plug from the power

supply.

Replacing the Line Spool (Model ART 23 G)

Hold the spool plate 14 in position.

Turn the empty spool 16 counter-clockwise to re-

move.

Pull approx. 9 cm of line out of the new/refilled spool.

Screw the new/refilled spool on the spool plate as far

as possible, as shown in figure G1.

Clasp the line between the studs of the spool plate as

shown in figure G1.

Replacing the Line Spool

(Model ART 23 GF/GFS/GFSV)

Hold the spool plate 14 in position.

Turn the spool cover 17 counter-clockwise and re-

move, as shown in figure H.

Take the empty spool 18 out from the spool cover.

Thread the line of the new/refilled spool through the

eyehole 19 and place the spool in the spool

cover 17.

Pull approx. 9 cm of line out of the spool.

Place spool with cover on the spool plate 17 in the

correct position (bayonet fastening), press down and

turn fully right, as shown in figure H.

Replacing the Line Spool

(Model ART 25 GSA/GSAV/ERGOPOWER)

Hold the spool plate 14 in position.

Press the locking tabs and remove the spool

cover 17.

Take the empty spool 18 out from the spool cover.

Place the new/refilled spool 18 in the spool plate 14

,the cord eyes 19 must rest in the slots of the spool

plate 14

Pull approx. 9 cm of line out of the spool.

Refit the spool cover 17 . A distinct latching must be

felt when pressed on.

Refilling Line

(Model ART 23 G/GF/GFS/GFSV)

Take out the spool 18 as described above.

Press the cover ring 20 together as shown in figure I,

push it forward and detach over the smaller diameter

of the spool.

Feeding the Line

Maintenance

F016 L69 858.book Seite 4 Freitag, 6. Juli 2001 11:50 11

16 • F016 L69 858 • 07.01

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch ART 23 GSA Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info