Bedienungsanleitung Bosch ART 35 (Seite 11 von 197) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

707805

Zoom out

Zoom in

Vorherige Seite

1/197

Nächste Seite

English | 11

Bosch Power Tools F 016 L81 763 | (29.8.17)

Keep the supply cables away from mov-

ing hazardous parts and avoid damage

to the cables; this can lead to contact

with live parts.

The connections (plugs and sockets)

should be kept dry and off the ground.

The supply cables must be inspected

for signs of damage at regular intervals

and may only be used if in perfect con-

dition.

If the supply cable on the product is

damaged, it must only be replaced by a

Bosch Service Centre.

Only use approved extension cables.

Extension cords, cables, leads, reels

should only be used if they comply with

EN 61242/IEC 61242 or

IEC 60884-2-7.

If you want to use an extension cable

when operating your product, only the

following cable dimensions should be

used:

– Nominal Conductor Area of

1.25 mm

or 1.5 mm

– Maximum length of 30 m for a Cord

Extension Set or maximum length of

60 m for a Cable Reel with Residual

Current Device (RCD

Note: If an extension cable is used it

must be earthed and connected

through the plug to the earth cable of

your supply network in accordance

with prescribed safety regulations.

If in doubt contact a qualified electri-

cian or the nearest Bosch Service Cen-

tre.

WARNING! Inadequate exten-

sion cables can be dangerous.

Extension cable, plug and

socket must be of watertight con-

struction and intended for outdoor

use.

For products not sold in GB:

WARNING: For your safety, it is re-

quired that the plug attached to the

product is connected with the exten-

sion cord. The coupling of the exten-

sion cord must be protected against

splash water, be made of rubber or

coated with rubber. The extension cord

must be used with a cable strain relief.

Products sold in GB only: Your prod-

uct is fitted with a BS 1363/A ap-

proved electric plug with internal fuse

(ASTA approved to BS 1362).

If the plug is not suitable for your

socket outlets, it should be cut off

and an appropriate plug fitted in its

place by an authorised customer ser-

vice agent. The replacement plug

should have the same fuse rating as

the original plug.

The severed plug must be disposed of

to avoid a possible shock hazard and

should never be inserted into a mains

socket elsewhere.

Products sold in AUS and NZ only:

Use a residual current device (RCD)

with a rated residual current of 30 mA

or less.

Symbols

The following symbols are important for reading and under-

standing the operating instructions. Please take note of the

symbols and their meaning. The correct interpretation of the

symbols will help you to use the garden product in a better

and safer manner.

OBJ_BUCH-1800-004.book Page 11 Tuesday, August 29, 2017 8:22 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch ART 35 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info