Bedienungsanleitung Bosch AXT Rapid 2000 (Seite 11 von 205) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

591560

Zoom out

Zoom in

Vorherige Seite

1/205

Nächste Seite

English | 11

Bosch Power Tools F 016 L81 148 | (22.10.14)

Keep your face and body away from

the chute assembly.

Do not allow hands or any other part

of the body or clothing inside the

chute assembly, discharge chute or

near any moving part.

Keep proper balance and footing at all

times. Do not overreach. Never stand

at a higher level than the base of the

machine when feeding material.

Always stand clear of the discharge

zone when operating the machine.

When feeding material into the ma-

chine be extremely careful that pieces

of metal, rocks, bottles, cans or other

foreign objects are not included.

If the cutting mechanism strikes any

foreign object or if the machine

should start making any unusual

noise or vibration, immediately

switch off and allow the cutter to

stop. Remove the plug from the

mains supply and take the following

steps:

– Inspect for damage.

– Replace or repair any damaged

parts.

– Check for and tighten any loose

parts.

Do not attempt to repair the machine

unless you are qualified to do so.

Do not allow processed material to

build up in the discharge zone; this

may prevent proper discharge which

can result in kickback of material

through the chute assembly.

If the machine becomes clogged,

switch off and allow the cutter to

stop. Remove the plug from the

mains supply before clearing debris.

Check if guards and protective devic-

es are undamaged and properly

mounted. Before using, carry out any

necessary maintenance and repairs.

Do not tamper with the motor speed

control settings. Contact a Bosch ap-

proved service agent if a problem ex-

ists.

Keep the motor cooling vents clean of

debris and other accumulations to

prevent damage to the motor or pos-

sible fire.

Never pick up or carry the machine

while the motor is running.

Switch off, allow the cutter to stop

and remove the plug from the mains

supply whenever you leave the work

area.

Do not tilt the machine while it is run-

ning.

Do not expose the machine to rain.

Only store the machine in a dry place.

Maintenance and Storage

When the machine is stopped for ser-

vicing, inspection, or storage, or to

change an accessory, switch off and

remove the plug from the mains sup-

ply and allow the machine to cool.

Make sure that all moving parts have

come to a complete stop before mak-

ing any inspections, adjustments,

etc.

Maintain the machine with care and

keep it clean.

Examine the machine and replace

worn or damaged parts for safety.

Ensure replacement parts fitted are

Bosch approved.

OBJ_BUCH-2230-001.book Page 11 Wednesday, October 22, 2014 9:25 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch AXT Rapid 2000 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info