Bedienungsanleitung Bosch BDU 350 Active Line Plus 2017 (Seite 9 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

780233

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

English–3

Bosch eBike Systems 0 275 007 AD5 | (31.5.17)

Setting the Assistance Level

On the on-board computer you can set how much the eBike

drive assists you while pedalling. The assistance level can be

changed at any time, even while cycling.

Note: For individual versions, it is possible that the assistance

level is pre-set and cannot be changed. It is also possible that

less assistance levels are available for selection than listed

here.

The following assistance levels (max.) are available:

–“OFF”: The motor assistance is switched off, and the eBike

can be moved as a normal bicycle only by pedalling. The

push assistance cannot be activated in this assistance

level.

–“ECO”: Effective assistance at maximum efficiency for

maximum cruising range

–“TOUR”: Uniform assistance, for touring with long cruising

range

–“SPORT”: Powerful assistance for sportive riding off road

as well as for urban traffic

–“TURBO”: Maximum assistance, supporting highest

cadence for sportive riding

The motor output requested appears on the display of the on-

board computer. The maximum motor output depends on the

selected assistance level.

Switching the Push-assistance mode On/Off

The push-assistance feature makes it easier to push the

eBike. The speed in this function depends on the set gear and

cannot exceed 6 km/h (max.). The lower the set gear, the low-

er the speed in the push-assistance function (at full output).

The push-assistance function may only be used when

pushing the eBike. Danger of injury when the wheels of

the eBike do not have ground contact while using the push-

assistance function.

To activate the push-assistance function, briefly press

button “WALK” on your on-board computer. After activation,

press button “+” within 3 s and keep it pressed. The eBike

drive is switched on.

Note: The push assistance cannot be activated in the “OFF”

assistance level.

The push assistance is switched off as soon as one of the

following occurs:

– You release the “+” button;

– The wheels of the eBike are prevented from turning (e.g.

by braking or being hit by your leg);

– The speed exceeds 6 km/h.

Note: On some systems the push-assistance function can be

started directly by pressing the “WALK” button.

Depending on the statutory specifications in some countries,

the push-assistance function may vary by region.

Switching bike lights on/off

In the version which has the bike lights powered by the eBike

system, the front and rear lights can be switched on and off at

the same time via the on-board computer.

Notes on Riding with the eBike System

When does the eBike Drive Unit Operate?

The eBike drive unit assists you when riding, as long as you

step into the pedals. Without pedaling, there is no assistance.

The motor output always depends on the amount of your

pedaling power.

When applying less pedaling power, the assistance or support

will be lower than when applying a lot of pedaling power. This

applies independent of the assistance Level.

The eBike drive automatically switches off at speeds in excess

of 25 km/h. When the speed falls below 25 km/h, the drive is

automatically available again.

An exception applies to the push-assistance function, in

which the eBike can be pushed at low speed without pedal-

ling. The pedals may also rotate when the push assistance is

used.

The eBike can also be ridden as a normal bicycle without as-

sistance at any time, by either switching off the eBike system

or setting the assistance level to “OFF”. The same applies

when the battery pack is empty.

Interaction of the eBike System with the Bicycle Gears

The bicycle gears should be used as with a normal bicycle,

even with eBike motor assistance (please observe the operat-

ing instructions of your eBike).

Independent of the type of gearing, it is recommended to

briefly interrupt the pedaling while changing gears. This

makes changing gears easier and reduces the wear of the

drive train.

By selecting the right gear, you can increase the speed and

range with the same pedaling effort.

Assistance Level Assistance Factor*

“ECO” 40 %

“TOUR” 100 %

“SPORT” 180 %

“TURBO” 270 %

* The assistance factor may vary on the individual versions.

OBJ_BUCH-3139-001.book Page 3 Wednesday, May 31, 2017 12:10 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch BDU 350 Active Line Plus 2017 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info