Bedienungsanleitung Bosch BDU 365 (Seite 12 von 36) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

733040

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

English – 2

0 275 007 XD3 | (14.01.2019) Bosch eBike Systems

Product description and

specifications

Intended use

The drive unit is intended exclusively for driving your eBike

and must not be used for any other purpose.

In addition to the functions shown here, changes to software

relating to troubleshooting and functional enhancements

may be introduced at any time.

Product features

Individual illustrations in these operating instructions may

differ slightly from the actual conditions depending on the

equipment of your eBike.

The numbering of the components shown refers to the illus-

trations on the graphics pages at the beginning of the

manual.

(1)

Drive unit

(2)

Speed sensor

(3)

Speed sensor spoke magnet

Technical data

Drive unit Active Line Active Line Plus Performance Line

Product code BDU310 BDU350 BDU365

Continuous rated power W 250 250 250

Torque at drive, max. Nm 40 50 65

Rated voltage V= 36 36 36

Operating temperature °C −5 to +40 −5 to +40 −5 to +40

Storage temperature °C −10 to +50 −10 to +50 −10 to +50

Protection rating IP 54 (dust- and

splash-proof)

IP 54 (dust- and

splash-proof)

IP 54 (dust- and

splash-proof)

Weight, approx. kg 3 3.3 3.5

The Bosch eBike system uses FreeRTOS (seehttp://www.freertos.org).

Bicycle lights

Voltage approx.

V= 12

Maximum power

– Front light W 17.4

– Tail light W 0.6

A) Depends on legal regulations, not possible in all country-specific models via the eBike battery

B) When changing the bulbs, ensure that they are compatible with the Bosch eBike system (ask your bicycle dealer) and are suitable for the

specified voltage. Bulbs must only be replaced with bulbs of the same voltage.

Inserting a bulb incorrectly can cause it to blow.

Assembly

Inserting and removing the battery

For inserting and removing the eBike battery in/from the

eBike, please read and observe the battery operating in-

structions.

Checking the speed sensor (see figure A)

The speed sensor (2) and its spoke magnet (3) must be fit-

ted such that the spoke magnet moves past the speed

sensor at a distance of at least 5 mm and at most 17 mm

with each rotation of the wheel.

Note: If the distance between the speed sensor (2) and the

spoke magnet (3) is too small or too large, or if the speed

sensor (2) is not properly connected, the speedometer dis-

play will fail and the eBike drive unit will operate in emer-

gency mode.

Should this occur, loosen the screw of the spoke magnet (3)

and fasten the spoke magnet to the spoke such that it runs

past the marking on the speed sensor at the correct clear-

ance. If the speed is still not being indicated on the speedo-

meter display after doing this, please contact an authorised

bicycle dealer.

Operation

Start-up

Requirements

The eBike system can only be activated when the following

requirements are met:

– A sufficiently charged battery is inserted (see battery op-

erating instructions).

– The on-board computer is properly inserted in the holder

(see on-board computer operating instructions).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch BDU 365 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info