Bedienungsanleitung Bosch BGLS4 (Seite 49 von 123) (Alle Sprachen)

700848

Zoom out

Zoom in

Vorherige Seite

1/123

Nächste Seite

Figure

Holding the power cord by the plug, pull out to the

required length and insert the plug into the mains

socket.

Figure Switching on and off

● Press the ON/OFF button in the direction of the

arrow to switch your vacuum cleaner on.

Figure Controlling the suction level

The suction level can be inﬁnitely adjusted to the level

required by turning the control knob in the direction of

the arrow.

Low power range =>

For vacuuming delicate materials,e.g.

upholstery, curtains, etc.

Medium power range =>

For the daily vacuuming of light

dirt deposits.

High power range =>

For vacuuming durable ﬂoor coverings,

hard ﬂoors and heavily soiled surfaces.

Vacuuming

Please note:

Floor tools are subject to a certain amount of wear,

depending on the type of hard ﬂoor you have (e.g.

rough, rustic tiles). Therefore, you must check the

underside of the ﬂoor tool at regular intervals. Worn

undersides of ﬂoor tools may have sharp edges that

can damage sensitive hard ﬂoors, such as parquet or

linoleum. The manufacturer does not accept any

responsibility for damage caused by worn ﬂoor tools.

Figure

Set the adjustable ﬂoor tool:

Rugs and carpets =>

Hard ﬂoors =>

If you are vacuuming up relatively large particles, make

sure that you vacuum them up successively and

carefully to ensure that the vacuum channel of the ﬂoor

tool does not become blocked. If necessary, you should

raise the nozzle in order to better vacuum up the dirt

particles.

Figure Vacuuming with accessories

Attach the nozzles to the suction pipe or hand grip as

required:

a)Crevice nozzle for vacuuming crevices and corners,

etc.

b)Upholstery nozzle for vacuuming upholstered

furniture, curtains, etc.

c)Hard-ﬂoor nozzle*

- with clip-in edge cleaning bristles:

For gentle but effective cleaning of hard ﬂoor

coverings (tiles, parquet, etc.)

- without edge cleaning bristles:

For cleaning dirt in gaps and cracks

11*

● The edge cleaning bristles can be removed by

pushing the two catches in the direction of the

arrows.

Drill dust nozzle

Figure

a)Secure the drill dust nozzle to the handle and then

place against the wall, so that the nozzle drill hole

opening sits directly over the hole to be drilled.

b)Select the lowest power setting and then switch on

the vacuum cleaner.

Suction holds the drill dust nozzle in the required

position.

c)Depending on the surface of the wall to be drilled it

may be necessary to readjust the power to a higher

setting to ensure the drill dust nozzle is ﬁrmly

attached.

Any ﬁne particles are automatically vacuumed up.

Figure

You can use the parking aid on the back of the vacuum

cleaner if you wish to stop vacuuming for a short time.

● Once you have switched off the appliance, slide the

hook on the ﬂoor tool into the recess on the rear of

the appliance.

Figure

To overcome obstacles, e.g. steps, the appliance can

also be carried by the handle on the appliance body.

When the work is done

Figure

a)Pull out the mains plug.

b)Brieﬂy pull on the power cord and then release it (the

power cord retracts automatically).

Figure

To store/transport the appliance, you can use the

storage aid on the underside of the appliance.

a)Stand the appliance upright on its end.

b)Slide the hook on the ﬂoor tool into the recess on the

underside of the appliance.

Changing the ﬁlter

Please note: Always switch off the appliance before

changing the ﬁlter.

Replacing the dust bag

Figure

Appliances with ﬁlter replacement indicator:

● If the ﬁlter replacement indicator in the lid is ﬁlled

completely when the ﬂoor tool is lifted from the ﬂoor

with the highest suction level selected, the dust bag

must be changed, even though it may not yet be full.

Even if the dust bag is not full, it may still need to be

changed due to the type of dust that has been

vacuumed. First check that the nozzle, suction pipe

and ﬂexible hose are not blocked, as this would also

lead to the ﬁlter replacement indicator being

triggered.

12*

depending on model

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch BGLS4 Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info