Bedienungsanleitung Bosch BSGL5333 (Seite 49 von 122) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

707927

Zoom out

Zoom in

Vorherige Seite

1/122

Nächste Seite

Dependent on model

Changing the ﬁlter

Please note: Always switch off the appliance before

changing the ﬁlter.

Replacing the bag

Figure

● If the dust bag change indicator in the lid is ﬁlled completely

when the ﬂoor tool is lifted from the ﬂoor with the highest

suction level selected, the dust bag must be changed, even

though it may not yet be full. Even if the dust bag is not full,

it may still need changing, due to the type of dust which has

been vacuumed. First check that the nozzle, suction pipe

and ﬂexible hose are not blocked, as this would also lead to

the dust bag change indicator being triggered.

Figure Opening the lid

● Open the lid by moving the locking lever in the direction of

the arrow.

Figure

a) Seal the dust bag by pulling the sealing plate, and remove

the bag.

b)Slide the new dust bag into the holder up to the stop.

Please note: the lid will only close if a dust bag has been

inserted.

Cleaning the motor protection filter

The motor protection filter should be cleaned regularly by

tapping out the dirt and rinsing.

Figure

● Open the dust bag compartment lid.

Figure

● Remove the motor protection filter from

the appliance in the direction of the arrow.

● Disconnect the motor protection filter from the Bionic filter.*

● Clean the motor protection filter by tapping out the dirt.

● If it is very dirty, the motor protection filter should be rinsed.

The filter must then be left to dry for at least 24 hours.

Please note: the Bionic filter must not come into contact

with water, as this will adversely affect the correct operation

of the filter.

● After cleaning, place the Bionic filter onto the motor

protection filter as necessary and push both filters into the

appliance.

● Close the dust bag compartment lid.

Replacing the Bionic filter

If your appliance is equipped with a Bionic filter, it should be

replaced once it begins to lose its effect (after approx. 1 year).

Figure

● Open the dust bag compartment lid.

Figure

● Remove the motor protection filter

together with the Bionic filter from the appliance.

● Remove the old Bionic filter from the motor protection filter

and dispose of it.

● Place the Bionic filter onto the motor protection filter.

● Push the filters into the appliance and close the dust bag

compartment lid.

20*

23*

24*

● The motor protection filter must also be inserted into the

appliance if you no longer wish to use the Bionic filter

Replacing the exhaust filter

Replacing the micro-hygiene filter

This should be replaced with every replacement ﬁlter pack.

Figure

● Open the dust bag compartment lid.

Figure

● Release the ﬁlter holder by turning the locking lever in the

direction of the arrow.

● Remove the micro-hygiene ﬁlter. Insert the new micro-

hygiene ﬁlter into the appliance.

● Insert the ﬁlter holder in the appliance and lock it in place.

Cleaning the Hepa* exhaust filter

The Hepa* ﬁlter is designed so that it does not need to be

replaced, provided the appliance is used as intended in the

household.

To ensure that the vacuum cleaner is working at its optimum

power level, the Hepa* ﬁlter should be rinsed out after one

year. The ﬁltering action of the ﬁlter remains intact, even if the

ﬁlter surface becomes discoloured.

Figure

● Open the dust bag compartment lid.

Figure

● Unlock the Hepa* ﬁlter by moving the locking tab in the

direction of the arrow, and remove it from the appliance.

● Tap out the ﬁlter unit and rinse it under running water.

Alternatively, the unit can be cleaned in a washing machine

at max. 30 °C using a gentle programme and the lowest spin

speed.

TIP: To protect other laundry items, put the ﬁlter unit into a

laundry bag.

● Once the Hepa* ﬁlter has dried completely (at least 24

hours), insert it back into the appliance and lock it in place.

● Close the rear ﬂap.

After vacuuming ﬁne dust particles (e.g. gypsum, cement, etc.),

clean the motor protection ﬁlter by tapping it out or, if

necessary, replace the motor protection ﬁlter and exhaust

ﬁlter.

Care

Always switch off the vacuum cleaner and disconnect

it from the mains before cleaning the vacuum cleaner. The

vacuum cleaner and plastic accessories can be cleaned with a

commercial plastic cleaner.

Do not use abrasive agents, glass or all-purpose cleaning

products. Never immerse the vacuum cleaner in water.

If necessary, the dust compartment can be cleaned with a

second vacuum cleaner or simply wiped with

a dry cloth or dusting brush.

Subject to technical modiﬁcations.

26*

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch BSGL5333 Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info