Bedienungsanleitung Bosch Compress 3000 - HP 200-1 E AI-F (Seite 11 von 40) (Englisch)

697410

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

6 720 646 804

Installation instructions

Fig. 6

A 27” minimum vertical clearance is required to remove

the filter for cleaning and to replace the anode rod. The

hot and cold water plumbing and electrical connections

must not interfere with the removal of the filter.

Fig. 7

Condensation drain

The unit has a condensate drain, therefore a drain must

be available in close proximity to the unit. The drain must

be no higher than 36” above the floor (laundry drain is

acceptable).

If no drain is available, then a common condensate

pump with a capacity no less than 1 gallon/day must be

purchased from a local builder and supply store and

installed.

3.3 Venting (specifications and vent

runs)

Venting the outlet air of the water heater to another

room may be an option for specific applications. See

Section 3.6.

• Duct diameter: 8”

• Maximum outlet duct length: 16.5 feet

• Maximum Air flow: 219 CFM

• Maximum no. of elbows: 1.

The vent collar accessory (see Fig. 2) must be installed

in order to accommodate the required 8" diameter vent

pipe. Line up tabs on vent collar with slots in vent

opening. Rotate to lock into place.

If terminating venting to the outdoors, pitch horizontal

pipe downward towards termination 1/4" per foot to

avoid damage from rain.

3.4 Water piping

3.4.1 Inlet - Outlet connections

Refer to the illustration below for suggested typical

installation. The installation of unions or flexible copper

connectors is recommended on the hot and cold water

connections so that the water heater may be easily dis-

connected for servicing if necessary. The HOT and

COLD water connections are clearly marked and are

¾”NPT on all models.

IMPORTANT: Do not apply heat to the HOT or COLD

water connections. If sweat connections are used,

sweat tubing to adapter before fitting the adapter to the

water connections on heater. Any heat applied to the

hot or cold water connection will permanently damage

the dip tube.

Fig. 8 Typical installation

3.4.2 Dielectric union (recommended acces-

sory)

Different metals between plumbing and tank materials

and additionally the effect of hot water can cause

corrosion of one of the metals (generally the one in the

tank is the metal attacked)

The Dielectric union will avoid any physical contact

between the two metals, acting as an effective insulator

and preventing this attack. How quick this corrosion

progresses, if at all, depends on the content of your

water, its pH, the dissolved minerals and the metals

involved.

5”½5”½

6720646804-06.1V

27”

6720646804-05.1V

Install a shut-off valve in the cold water line

near the water heater. This will enable eas-

ier service or maintenance of the unit later.

6720646804-09.1V

6” air gap

Relief discharge

line to suitable

open drain

6’ drain hose

Thermal expansion

tank (if required)

To cold water

supply

Hot water outlet

to fixtures

Union

Temperature and

pressure relief valve

(shown in different

location for clarity)

Drain valve

Jacket

access panel

Jacket

access panel

Auxiliary catch

pan 2” maximum

Electrical junction box

(use only copper

conductors)

To electrical

distribution panel

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch Compress 3000 - HP 200-1 E AI-F Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info