Bedienungsanleitung Bosch Compress 3000 - HP 200-1 E AI-F (Seite 24 von 40) (Englisch)

697410

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

6 720 646 804

Maintenance and repair

The decorative front cover must be removed to access

the valve.

In order to drain the water heater completely:

B Turn off the cold water supply.

B Open a hot water faucet or lift the handle on the relief

valve to admit air to the tank.

Fig. 17

B Open the drain valve.

5.5 Vacation and Extended Shutdown

If the water heater is to remain idle for an extended

period of time, the power and water to the appliance

should be turned off to conserve energy and prevent the

buildup of dangerous hydrogen gas.

The water heater and piping should be drained if they

might be subjected to freezing temperatures. After a

long shutdown period, the water heater’s operation and

controls should be checked by qualified service person-

nel. Make certain the water heater is completely filled

again before placing it in operation.

5.6 Cleaning the Filter

In the Auto and Economic modes, the heater moves air

through the system and out the back of the unit. The fil-

ter is in place to protect the evaporator from dirt and

dust.

A clean air filter is important to get the highest effi-

ciency. Occasionally this filter will need to be cleaned

(minimum is once a year).

B Leave the power on.

B Remove the filter from the top of the unit.

It is located in the top of the unit behind the hot and cold

inlet pipes.

B Grasp the plastic handle

B Slide the filter straight up until it clears the shroud.

Once it has beed removed, the filter can be wiped

clean with a damp rag or rinsed with warm water.

Fig. 18

Once the filter has been cleaned, it can be replaced by

aligning it into the slot in the top of the unit and sliding

it down into place. When the handle is flush with the top

of the shroud, it is seated.

When the clean filter has been reinstalled:

B Press ENTER and DOWN keys simultaneously for 2

seconds.

IMPORTANT: A dirty filter will make the system work

harder and result in a reduction of efficiency and

possible damage to the system. In order to get the best

energy efficiency available, make sure your filter is

clean.

5.7 Clearing the Condensation Drain

Tubes

There are two drain hoses that are attached to the back

of the heater. If both of these get clogged, water will

spill down the outside of the unit.

The primary drain is intended to carry all condensate

away. If it is clogged or if the hose is kinked, the conden-

sate will exit the secondary drain tube and onto the floor.

This is intended as a notification to the user that the pri-

mary drain is clogged.

B Remove the drain hose.

B Clear any debris and reattach.

Fig. 19

Note: refer to the Hydrogen Gas Caution

in the Operating Instructions.

If the filter gets too dirty, the unit will auto-

matically switch to Standard Electric

mode and energy savings will be lost.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch Compress 3000 - HP 200-1 E AI-F Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info