809317
16
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
Installation
Compress 3400i AWS – 6721852066 (2023/01)
16
Coding switches A and P must not be adjusted! Otherwise malfunctions
and faults will occur.
Important: check the coding when a replacement part is used ( Fig.
36).
5.7.3 CAN-BUS
NOTICE
Malfunction due to faults!
Power circuit cables (230V~) cannot be near any CAN-BUS, sensor and
other signal circuit cables (12V DC).
Ensure there is a minimum distance of 100 mm between power
circuit cables and CAN-BUS, sensor and other signal circuit cables.
CAN-BUS: do not connect 12V direct voltage output "Out 12V DC" on the
installation module.
NOTICE
Mixing up the 12V and CAN-BUS connections will result in a system
fault!
The communication circuits are not designed for a constant voltage of
12V.
Make sure that both cables are connected to the correspondingly
marked connections on the printed circuit board (CAN high / CAN
low).
The outdoor unit and indoor unit are connected to each other via a
communication cable, the CAN-BUS.
A LIYCY cable (TP) 3x0.75 mm2 (or equivalent) is suitable as an
extension cable outside of the unit. Alternatively, twisted pair cables
approved for outdoor use with a minimum cross-section of 0.75 mm2
can be used. One of the shielded ends must be connected to the nearest
grounding terminal in the indoor unit structure. The other end cannot be
connected to the grounding or any metal part of the outdoor unit
structure.
The maximum permissible cable length is 30 m.
The Can Termination Switch marks the start and end of the CAN-BUS
connection. Make sure that the right boards are terminated and that all
other boards within the CAN-BUS connection are not terminated.
Fig. 12 CAN-BUS connection
[1] Indoor unit
[2] Outdoor unit
5.7.4 EMS BUS
NOTICE
Malfunction due to faults!
Power circuit cables (230V~) cannot be near any EMS-BUS, sensor and
other signal circuit cables (12V DC).
Ensure there is a minimum distance of 100 mm between power
circuit cables and EMS-BUS, sensors and other signal circuit cables.
The control unit is connected via the EMS-BUS to the installer module of
the indoor unit.
The control unit is supplied with power via the BUS cable. The polarity of
the two EMS-BUS cables is irrelevant.
The following applies to accessories that are connected to the EMS-BUS
(see also the installation instructions for the respective accessories):
If several BUS units are installed, there must be a minimum spacing of
100 mm between them.
If several BUS units are installed, connect them in parallel or in a star
configuration.
Use cable with a minimum cross-section of 0.5 mm2.
In case of external inductive interferences (e.g. from PV systems),
use screened cables. Connect only one end of the cable shield to the
nearest ground.
2
1
0010036947-001
LN
Can H
Can L
GND
Out 12V DC
CAN high
CAN low
gnd
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch Compress 3400i AWS wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Bosch Compress 3400i AWS

Bosch Compress 3400i AWS Bedienungsanleitung - Englisch - 2 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info