Bedienungsanleitung Bosch Condens GC7000WP (Seite 30 von 52) (Englisch)

780622

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Operation

Condens 7000 WP – 6721841195 (2022/01)

Max. output • 10 ... 100 % Pump output at maximum heat output. Only available if

Pump range map is set to 0.

Pump block time • 0 ... 24 × 10 seconds The internal pump is locked until the external 3-way valve

has reached its end position.

Pump overrun • 1 2 ... 60 min, 24 h Overrun time of the heating pump: pump overrun begins

when heat demand ends.

Ventilation func. • Off

•Auto

•On

The venting function can be switched on after

maintenance work.

During ventilation, the following appears in the info area

of the standard display Ventilation func.

Siphon fill. prog. • Off (only permitted when maintenance is in

progress)

•On, boiler min.

• On, heating min.

The siphon filling program is activated in the following

cases:

• Once the device is switched on using the On/Off

switch

• Once the burner was not in operation for at least

28 days

• Once the operating mode is switched from summer to

winter mode

• Once the factory settings of the device have been

restored

The next time there is a heat demand for heating, the

appliance is held at low heat output for 15 minutes. The

siphon filling program remains active until the device was

in operation with low heat output for 15 minutes.

When the trap filling program is running, the following

appears in the info area of the standard display Siphon

fill. prog.

3-WV mid. pos. • No

•Yes

The function ensures that the system is fully drained and

that the motor can be easily removed. The 3-way valve

remains at the middle position for approx. 15 minutes.

Min. Sys. Pres. • 0.6 0.8 bar

Target Sys. Pres. • 1.0 … 1.3 … 1.7 bar

Maintenance

Maintenance type • Without

• Burner run time: 1000 ... 6000 h

• Service date1)

• Boiler run time: 1 ... 72 months

Limit values

Max. flow temp. • 30 ... 85 °C Limits the adjustment range for the flow temperature.

Max. DHW temp. • 35 ... 60 ... 80 °C Limits the adjustment range for the domestic hot water

temperature.

Min. boiler outp. • 14 ... 50% Minimum heat output. Minimum setting value may vary

depending on appliance output.

Heating curve

Enable • Yes

•No

When connecting a weather-compensated control unit,

no adjustment at the device is required. The system

control unit optimises this setting. This service function

activates a simple, weather-compensated controller with

a linear heating curve. Depending on the on/off input, the

heating is switched on or off.

Htg. curve base • 20 … 90 °C This is only displayed if the control unit was activated.

This can be used to set the base point of the heating

curve, which corresponds to an outside temperature of

+20 °C.

Htg. curve end • 20 ... 90 °C This is only displayed if the control unit was activated.

This can be used to set the base point of the heating

curve, which corresponds to an outside temperature of -

10 °C.

Meu item Settings/adjustment range Remark/restriction

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch Condens GC7000WP Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch Condens GC7000WP

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info