Bedienungsanleitung Bosch Condens GC7000WP (Seite 44 von 52) (Englisch)

780622

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Troubleshooting

Condens 7000 WP – 6721841195 (2022/01)

Table 20 Indicators and fault displays

11.1.3 Faults that are not displayed

Table 21 Faults that are not shown on the display

Fault display: System pressure too low

If the system pressure in the heating system falls below the minimum

pressure that has been set, the display shows the message LoPr => L0.X

bar. The system pressure is too low.

▶ Fill the heating system.

2966 B Flow temperature rise in heat exchanger too

rapid

1. Ensure that the heating circulation is working correctly.

2. Check pump setting, adjust to match heating system if necessary.

3. Connect the plug to the temperature sensor correctly.

4. Connect the plug to the control device correctly.

5. Attach the temperature sensor correctly.

6. Check the temperature sensor, replace if necessary.

7. Check temperature sensor connecting lead, replace if necessary.

2967 The temperature difference between supply

temperature sensor and temperature

sensor at heat exchanger is too large

–

2968 Refilling system pressure –

2970 Pressure drop in heating system too rapid –

2971 B System pressure too low 1. Vent the heating system.

2. Check the heating system for tightness.

3. Top up water until the target pressure is reached.

4. Check the pressure sensor, replace if necessary.

5. Check the pressure sensor cable, replace if necessary.

2972 Mains voltage too low 1. Establish supply voltage of at least 196 VAC.

2. Replace burner control unit.

3071 No communication with remote control 1. Check configuration.

2. Check cabling.

Device faults Remedy

Combustion noises too loud, rumbling noises ▶ Check the gas type.

▶ Check the gas supply pressure.

▶ Check the flue system, clean or repair as necessary.

▶ Check the gas/air ratio.

▶ Check the air/gas ratio control valve, replace if required.

Flow noises ▶ Set the pump rate or pump characteristic map correctly and match to the maximum

output.

Heat-up takes too long. ▶ Set the pump rate or pump characteristic map correctly and match to the maximum

output.

Flue gas values incorrect, CO content too high. ▶ Check the gas type.

▶ Check the gas supply pressure.

▶ Check the flue system, clean or repair as necessary.

▶ Check the gas/air ratio.

▶ Check the air/gas ratio control valve, replace if required.

Violent ignition, poor ignition. ▶ Check the ignition transformer with service function t01 for misfiring, replace if

required.

▶ Check the gas type.

▶ Check the gas supply pressure.

▶ Check the power supply.

▶ Check the electrodes with cable, replace if required.

▶ Check the flue system, clean or repair as necessary.

▶ Check the gas/air ratio.

▶ For natural gas: check the external gas flow monitor, replace if required.

▶ Check the burner, replace if required.

▶ Check the air/gas ratio control valve, replace if required.

No function, the display remains dark. ▶ Check the electrical wiring for damage.

▶ Replace defective cables.

▶ Check the fuse, replace if required.

Fault

code

Fault

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch Condens GC7000WP Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch Condens GC7000WP

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info