743473
12
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
Installation
CP1 – 6 720 645 612 (2012/10)
12
3Installation
3.1 Installing the condensate pump
When installing the condensate pump, observe the following:
Use suitable means to ensure moisture protection.
Fit the condensate pump horizontally near the appliance.
Position the condensate pump in easy access for maintenance and
inspection.
Use suitable rawl plugs for the base on which the condensate pump is
fitted.
Use different rawl plugs from those provided if required.
Test the load bearing capacity of the substrate.
Observe the maximum delivery head of 4.5 m (Æ Fig. 3 and Fig. 10).
Ensure the hose is routed correctly with a fall of 1 % (Æ Fig. 10).
B Position the condensate pump against the wall and level with a spirit
level.
B Mark the positions of the rawl plugs on the wall.
Fig. 5 Levelling the condensate pump
B Drill holes for the rawl plugs.
B Insert rawl plugs into the holes.
B Insert the screw halfway into the rawl plug.
B Remove fuse [1].
Fig. 6 Removing the fuse
[1] Fuse
B Hook the condensate pump onto the screws.
B Tighten the screws.
3.2 Connecting the condensate pump
B Fit supply hose [2] to the condensate drain in the appliance that
expels condensate.
B Fit supply hose [2] to condensate inlet connection [1] on condensate
pump [3].
Fig. 7 Fitting the supply hose
[1] Condensate inlet connection
[2] Supply hose Ø 28 mm (not part of standard delivery)
[3] Condensate pump
B Fit drain hose [3] to condensate drain [1] on condensate pump.
B Use an adapter if the hoses have different diameters (Æ Fig. 9).
B Fit locking device [4] and secure hose using hose clip [2].
Fig. 8 Fitting the drain hose
[1] Condensate drain
[2] Hose clip
[3] Ø 10 mm drain hose
[4] Locking device
NOTICE: Damage to the condensate pump due to
incorrect use.
B Never step on the casing.
B To prevent the thread from stripping, never place any
stresses on the hoses.
6 720 645 612-07.2ITL
6 720 645 612-12.1ITL
1
NOTICE: System damage due to corrosion
B Use plastic or stainless steel for on-site lines and
connection pieces that carry condensate (e.g. from
the flue to the boiler or neutralising system).
NOTICE: System damage
B Use the hose provided as part of the standard delivery
for the condensate drain.
6 720 645 612-11.2ITL
2
3
1
6 720 645 612-13.1ITL
1.
2.
3.
2
1
4
3
12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch CP1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info