Bedienungsanleitung Bosch CSG636BS2 (Seite 14 von 64) (Englisch)

563423

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

en Before using for the first time

KBefore using for the first

time

Before using for the first time

Before you can use your new appliance, you must

make some settings. You must also clean the cooking

compartment and accessories.

Before using for the first time

Before using the appliance for the first time, enquire

about the water hardness of your tap water from your

water supplier.

So that the appliance can reliably remind you to

decalcify it when required, you must correctly set your

water hardness range.

Caution!

The appliance may become damaged due to the use of

unsuitable liquids.

Do not use distilled water, highly chlorinated tap water

(> 40 mg/l) or other liquids.

Only use cold, fresh tap water, softened water or

uncarbonated mineral water.

Notes

■ If your water is very hard, we recommend that you

use softened water.

■ If you only use softened water, you can set the water

hardness range to "softened" in this case.

■ If you use mineral water, set the water hardness

range to "4 very hard".

■ If you use mineral water, you must only use non-

carbonated mineral water.

Initial use

After connecting the appliance to the power or following

a power cut, the settings for initial use are shown on the

display. It may take a few seconds for the instruction to

appear.

Note: You can change these settings at any time in the

basic settings. ~ "Basic settings" on page 24

Setting the language

The language is the first setting displayed. "German" is

the preset language.

1. Turn the rotary selector to set the required language.

2. Touch the next text field to confirm.

The next setting appears.

Setting the clock

The clock starts at "12:00".

1. Touch the "Clock" text field.

2. Set the clock using the rotary selector.

3. Touch the next text field to confirm.

The next setting appears.

Setting the water hardness

The default water hardness setting is "very hard".

1. Use the rotary selector to set the water hardness.

2. Touch the "Complete the settings" text field to

confirm.

A note appears in the display confirming that the initial

use has been completed.

Switch the appliance off using the ÿ On/Off button if

you do not need to use it.

Calibrating the appliance and cleaning the

cooking compartment

The boiling point of water depends on the air pressure.

During calibration, the appliance sets itself to the

pressure ratio at the installation location. This occurs

automatically during the first steam operation. This

results in a lot of steam.

Preparing the calibration

1. Remove the accessories from the cooking

compartment.

2. Remove leftover packaging, such as polystyrene

pellets, from the cooking compartment.

3. Before calibrating the appliance, wipe the smooth

surfaces in the cooking compartment with a soft, wet

cloth.

Water hardness range Setting

0 00 softened

1 (up to 1.3 mmol/l) 01 soft

2 (1.3 - 2.5 mmol/l) 02 medium

3 (2.5 - 3.8 mmol/l) 03 hard

4 (above 3.8 mmol/l) 04 very hard

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch CSG636BS2 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch CSG636BS2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info