Bedienungsanleitung Bosch CSG656BS7B (Seite 33 von 60) (Englisch)

746202

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

en Appliance door

Fitting panels

1. Open the appliance door fully and refit the

condensate trough. To do this, insert the trough from

above and rotate it at the bottom (fig. !).

2. Slide the intermediate glass panel back in and make

sure that it is sitting correctly at the bottom in the

retainer (fig. ").

3. Press down on the top of the intermediate glass

panel (fig. #).

4. Refit the seal on the left and right (fig. $)

5. Push in the inner glass panel.

Before sliding the panel in, make sure that the

glossy side of the panel is on the outside and the

cut-outs on the left and right are at the top.

The panel must be sitting correctly at the bottom in

the retainer (fig. %).

6. Push the inner panel in at the top (fig. &).

7. Put the cover back in place and press on it until you

hear it click into place (fig. ').

8. Open the appliance door again fully.

9. Close the two locking levers on the left and right

(fig. ()

10. Close the appliance door.

Caution!

Do not use the cooking compartment again until the

panels have been correctly fitted.







g





Trouble shooting en

3Trouble shooting

Tr oubl e s hoot i ng

If a fault occurs, there is often a simple explanation.

Before calling the after-sales service, please refer to the

fault table and attempt to correct the fault yourself.

Rectifying faults yourself

You can often easily rectify technical faults on the

appliance yourself.

If a dish does not turn out exactly as you wanted, you

can find many tips and instructions for preparation at

the end of the operating manual. ~ "Tested for you in

our cooking studio" on page 37

Fault Possible cause Notes/remedy

The appliance does not work. Faulty fuse. Check the circuit breaker in the fuse box.

Power cut Check whether the kitchen light or other kitchen appliances are working.

"Sprache Deutsch" appears on the

display.

Power cut Reset the language and the time.

The time does not appear when the

appliance is switched off.

Basic setting is changed. Change the basic setting for the clock display.

The appliance does not heat up; the

m symbol lights up on the display.

Demo mode is activated in the

basic settings.

Briefly disconnect the appliance from the mains (switch off the circuit breaker

in the fuse box) and then deactivate demo mode in the basic settings within 3

minutes.

The appliance will not start and

"Cooking compartment too hot"

appears on the display

The cooking compartment is

too hot for the selected dish

or type of heating

Allow the cooking compartment to cool down and start again

The rotary selector has fallen out of

the support in the control panel.

The rotary selector has been

accidentally disengaged.

The rotary selector can be removed. Simply place the rotary selector back in

its support in the control panel and push it in so that it engages and can be

turned as usual.

The rotary selector can no longer be

turned easily.

There is dirt under the rotary

selector.

The rotary selector can be removed. To disengage the rotary selector, simply

remove it from the support. Alternatively, press on the outer edge of the rotary

selector so that it tips and can be picked up easily.

Carefully clean the rotary selector and its support on the appliance using a

cloth and soapy water. Dry with a soft cloth. Do not use any sharp or abrasive

materials. Do not soak or clean in the dishwasher.

Do not remove the rotary selector too often so that the support remains sta-

ble.

Home Connect does not work cor-

rectly.

Go to www.home-connect.com

Operations with steam or descaling

do not start or do not continue

Water tank empty Refill water tank

The panel is open Close the panel

Descaling locks operations

with steam

Carry out descaling

Faulty sensor Call the after-sales service

The appliance prompts you to rinse The power supply was inter-

rupted or the appliance was

switched off during the desca-

ling process

Once the appliance is switched on again, rinse it twice

The appliance prompts you to descale

without the counter appearing before-

hand

The set water hardness range

is too low

Carry out descaling

Check the set water hardness range and adjust it, if necessary

Buttons flash Normal occurrence caused by

condensation behind the con-

trol panel

As soon as the condensation has evaporated, the buttons no longer flash

Cooked dishes turn out too moist or

too dry when cooking with steam-

assisted applications

The wrong steam intensity

was selected

Select a higher or lower steam intensity

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch CSG656BS7B Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info