Bedienungsanleitung Bosch D-tect 150 SV Professional (Seite 16 von 219) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

592019

Zoom out

Zoom in

Vorherige Seite

1/219

Nächste Seite

16 | English

1 619 929 J48 | (1.7.11) Bosch Power Tools

Robert Bosch GmbH, Power Tools Division

D-70745 Leinfelden-Echterdingen

Leinfelden, 19.05.2011

Assembly

Inserting/Replacing the Battery

To open the battery lid 4, press the latch 5 in the direction of

the arrow and remove the battery lid. Insert the batteries/

rechargeable batteries. When inserting, pay attention to the

correct polarity according to the representation on the inside

of the battery compartment.

The battery indicator b in the upper status line on the display

16 indicates the charge condition of the batteries/rechargea-

ble batteries.

Note: Pay attention to the changing battery symbol so that

the batteries/rechargeable batteries are replaced in time.

When the “Please change

batteries” warning indication

is indicated on the display 16,

the settings are saved and the

measuring tool switches off

automatically. Measurements

are no longer possible.

Change the batteries/

rechargeable batteries.

To remove the batteries/rechargeable batteries, press on the

rear end of a battery as indicated in the figure on the battery

lid ( ). The front end of the battery/rechargeable battery is

released from the battery compartment ( ), so that the bat-

tery/rechargeable battery can easily be removed.

Always replace all batteries/rechargeable batteries at the

same time. Do not use different brands or types of batteries/

rechargeable batteries together.

f Remove the batteries/rechargeable batteries from the

measuring tool when not using it for longer periods.

When storing for longer periods, the batteries/rechargea-

ble batteries can corrode and discharge themselves.

Operation

f Protect the measuring tool against moisture and direct

sun light.

f Do not subject the measuring tool to extreme tempera-

tures or variations in temperature. In case of large var-

iations in temperature, allow the measuring tool to ad-

just to the ambient temperature before switching it on.

In case of extreme temperatures or variations in tempera-

ture, the accuracy of the measuring tool and the display in-

dication can be impaired.

f Do not attach any stickers or name-plates to the sensor

area 9 on the back of the measuring tool. Especially

metal name-plates affect the measuring results.

f Use or operation of transmitting systems, such as

WLAN, UMTS, radar, transmitter masts or microwaves,

in the close proximity can influence the measuring

function.

Method of Operation (see figure B)

The measuring tool checks the

base material of sensor area 9

in measurement direction A to

the displayed measuring

depth. Measurement is possi-

ble only during movement of

the measuring tool in the direc-

tion of travel B and for a meas-

uring distance of at least

10 cm. Move the measuring

tool in a straight line with

light pressure over the wall

so that the wheels remain in

firm contact with the wall.

Objects are detected that

differ from the material of the wall. The object depth and, if

possible, the object material, are indicated on the display.

Optimum results are achieved when the measured distance is

at least 40 cm and the measuring tool is moved slowly over

the entire location to be checked. The tool’s method of opera-

tion ensures reliable detection of outer object edges that run

transverse to the measuring tool’s movement direction.

Therefore, always move crossways over the area to be

checked.

If several objects are located one over the other in the wall,

the object that is indicated in the display is the one nearest to

the surface.

The representation of the properties of detected objects in

the display 16 can deviate from the actual object properties.

This applies particularly for very thin objects, which are repre-

sented thicker in the display. Large cylindrical objects (e.g.

plastic or water pipes) can appear in the display smaller than

they actually are.

Detectable Objects

– Plastic pipes (e.g. water-carrying plastic pipes, as used in

floor/wall-heating systems, with at least 10 mm in diame-

ter; empty pipes with at least 20 mm in diameter)

– Electrical wiring (independent of whether carrying voltage

or not)

– Three-phase mains wiring (e.g. to the stove)

– Low-voltage wiring (e.g. for door bell, telephone

– Metal pipes, bars, beams of any type (e.g. steel, copper,

aluminium)

– Reinforcing steel

– Wooden beams

– Hollow spaces

Dr. Egbert Schneider

Senior Vice President

Engineering

Dr. Eckerhard Strötgen

Head of Product

Certification

Please change batteries

SENSO

OBJ_BUCH-1478-001.book Page 16 Friday, July 1, 2011 8:48 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch D-tect 150 SV Professional Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info