Bedienungsanleitung Bosch D-tect 150 SV Professional (Seite 19 von 219) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

592019

Zoom out

Zoom in

Vorherige Seite

1/219

Nächste Seite

English | 19

Bosch Power Tools 1 619 929 J48 | (1.7.11)

The summit of the curve is displayed in the small scale above

the operating-mode indication h in the form of a U. The object

depth and the material properties (as far as possible) are dis-

played. The maximum measuring depth is 15 cm.

f Conclusions on the object depth cannot be drawn from

the signal strength.

Changing the Display Modes

Note: Changing the display modes is possible in any operat-

ing mode.

To switch from the standard start display to rule mode, press

and hold selection button 10 or 12.

In the example, rule mode shows the same situation as in

figure D: Three steel bars equally apart. In rule mode, the clear-

ance between the detected object centres can be determined.

The measuring distance covered from the starting point (in

the example 20.1 cm) is displayed under the indication of the

object depth l.

The three objects are displayed as rectangles in the small rule

above the operating-mode indication h.

Note: Both the indication of the object depth l as well as the

material property m refer to the object pictured black in the

sensor.

To return to the standard start display, briefly press selection

button 10 or 12.

Note: Only the display is reset, not the measuring mode!

“Settings” Menu

To access the “Settings” menu, press the setup button 14.

To exit the menu, press the start button 11. The current set-

tings are saved. The standard start display for the measuring

process is activated.

Navigating in the Menu

Press the setup button 14 to scroll down.

Press the selection buttons 10 and 12 to select the values:

– Selection button 10 will select the right-hand or next value.

– Selection button 12 will select the left-hand or previous

value.

Language

In the “Language” menu, you can change the menu-guidance

language. The default setting is “English”.

Cut-off Time

In the “Cut- off time” menu, you can set certain time intervals

after which the measuring tool shall automatically shut off

when no measurements are taken or settings are carried out.

The default setting is “5 min”.

Light Duration

In the “Display illum.” menu, you can set a time interval, dur-

ing which the display 16 shall be illuminated. The default set-

ting is “30 sec”.

Brightness

In the “Brightness” menu, you can set the brightness of the

display backlight. The default setting is “Max”.

Tone Signals

In the “Tone signal” menu, you can limit when the measuring

tool shall give out an audio signal, provided that you have not

switched off the signal with the audio signal button 13.

– The default setting is “Wallobjects”: An audio signal

sounds after each button press, and whenever a wall ob-

ject is under the sensor range. Additionally, a short-beat

warning signal is given for “live” wires.

– With the adjustment “Live wire”, an audio signal sounds

after each button press, as does the warning signal for

“live” wires (short-beat signal) when the measuring tool in-

dicates a power line.

– With the adjustment “Keyclick”, an audio signal only

sounds when pressing a button.

Default Mode

In the “Defaultmode” menu, you can set the default operat-

ing mode that is to be pre-set after switching the measuring

tool on. The operating mode “Concrete Universal” is the de-

fault setting.

“Extended Settings” Menu

To access the “Extended settings” menu, press the setup but-

ton 14 and the On/Off button 15 at the same time when the

measuring tool is switched off.

To exit the menu, press the start button 11. The standard

start display for the measuring process is activated and the

settings are saved.

Navigating in the Menu

Press the setup button 14 to scroll down.

Press the selection buttons 10 and 12 to select the values:

– Selection button 10 will select the right-hand or next value.

– Selection button 12 will select the left-hand or previous

value.

3020 cm10 cm0cmcm

Signal View

Prev. Next

4.0 cm

20 19 18 21 22 23

4030 cm20 cm10 cmcm

Concrete Special

Prev. Next

20.1 cm

5.5 cm

OBJ_BUCH-1478-001.book Page 19 Friday, July 1, 2011 8:48 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch D-tect 150 SV Professional Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info