Bedienungsanleitung Bosch D-tect 150 SV (Seite 18 von 219) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544330

Zoom out

Zoom in

Vorherige Seite

1/219

Nächste Seite

18 | English

1 619 929 J48 | (1.7.11) Bosch Power Tools

Localisation of Objects

To localise objects, moving over the measuring path once is

sufficient.

When no object has been found, repeat the motion perpen-

dicular to the initial measuring direction (see “Method of

Operation”, page 16).

For precise localisation and marking of an object, move the

measuring tool back over the measuring path.

When an object is indicated centrally below the centre line k

in display 16, as in the example, you can mark it coarsely with

the top marking aid 1. This mark, however, will only be pre-

cise, when the object is positioned exactly vertical in the wall,

as the sensor range is located somewhat below the top mark-

ing aid.

For exact marking of the object on the wall, move the measuring

tool left or right until the found object is positioned below one of

the outer edges. When the found object, as an example, is indi-

cated centrical below the dashed right-hand line g in display

16, you can mark it precisely with the right marking aid 3.

The direction of a found object in a wall can be determined by

carrying out several offset measurements one after another

(see figure I and “Examples for Measuring Results”, page 20).

Mark and connect the respective measuring points.

By pressing the start button 11, the display of the objects found

can be deleted at any time and a new measurement started.

f Before drilling, sawing or routing into a wall, protect

yourself against hazards by using other information

sources. As the measuring results can be influenced

through ambient conditions or the wall material, there may

be a hazard even though the indicator does not indicate an

object in the sensor range (no audio signal or beep and and

the LED 17 lit green).

Changing the Operating Modes

Changing between different operating modes is possible with

selection buttons 10 and 12.

– Briefly press selection button 10 to select the next operat-

ing mode.

– Briefly press selection button 12 to select the previous op-

erating mode.

By selecting the operating modes, you can adapt the measur-

ing tool to different wall materials. The current setting is al-

ways shown in the operating-mode indication h of the display.

Concrete Universal (preset)

The operating mode “Concrete Universal” is suitable for

most applications in brickwork or concrete. Plastic and metal

objects as well as electrical wiring are displayed. Hollow spac-

es in brickwork or empty plastic pipes with a diameter of less

than 2 cm are possibly not displayed. The maximum measur-

ing depth is 8 cm.

Concrete Wet

The operating mode “Concrete Wet” is particularly suitable

for applications in wet concrete. Reinforcing steel, plastic and

metal pipes, as well as electrical wiring are displayed. Differ-

entiating between “live” and voltage-free conductors is not

possible. The maximum detection depth is 6 cm.

Please observe that concrete requires several months to dry

completely.

Concrete Special

The operating mode “Concrete Special” is particularly suita-

ble for detecting objects embedded deep in reinforced con-

crete. Reinforcing steel, plastic and metal pipes, as well as

electrical wiring are displayed. The maximum measuring

depth is 15 cm.

When too many objects are displayed, it may be possible that

you are moving directly alongside a reinforcement rod. In this

case, place the measuring tool a few centimetres aside and try

again.

Panel Heating

The operating mode “Panel Heating” is particularly suitable

for detecting metal, metal-composite and water-filled plastic

pipes, as well as for electrical wiring. Empty plastic pipes are

not displayed. The maximum measuring depth is 8 cm.

Drywall

The operating mode “Drywall” is suitable for finding wooden

beams, metal framing and electrical wiring in drywalls (wood,

gypsum board, etc.). Filled plastic pipes and wooden beams

are displayed identically. Empty plastic pipes are not detect-

ed. The maximum measuring depth is 8 cm.

Metal

The operating mode “Metal” is suitable for detecting metal

objects and “live” conductors when other operating modes in

different wall situations do not provide satisfactory results. In

such cases, the detection results will be more extensive, yet

less precise.

Signal View Mode

The operating mode “Signal View” is suitable for all materi-

als. The signal strength at the corresponding detection posi-

tion is displayed. In this operating mode, objects close to

each other can be precisely detected and complicated mate-

rial structures can be better evaluated based on the charac-

teristic of the signal. The maximum detection depth is 6 cm.

Concrete

Sensor

1.5 cm

0 cm

Concrete

Sensor

1.5 cm

0 cm

OBJ_BUCH-1478-001.book Page 18 Friday, July 1, 2011 8:48 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch D-tect 150 SV Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info