Bedienungsanleitung Bosch D-tect 150 (Seite 25 von 345) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544331

Zoom out

Zoom in

Vorherige Seite

1/345

Nächste Seite

English | 25

Bosch Power Tools 1 609 929 X40 | (30.8.10)

“Settings” Menu

To access the “Settings” menu, press the setup

button 14.

To exit the menu, press the start button 11. The

current settings are saved. The standard start

display for the measuring process is activated.

Navigating in the Menu

Press the setup button 14 to scroll down.

Press the selection buttons 10 and 12 to select

the values:

– Selection button 10 will select the right-hand

or next value.

– Selection button 12 will select the left-hand

or previous value.

Language

In the “Language” menu, you can change the

language of the menu navigation. The default

setting is “English”.

Cut-off Time

In the “Cut-off time” menu, you can set certain

time intervals after which the measuring tool

shall automatically shut off when no measure-

ments are taken or settings are carried out. The

default setting is “5 min”.

Light Duration

In the “Light duration” menu, you can set a time

interval within which the display 16 shall be illu-

minated. The default setting is “30 s”.

Brightness

In the “Brightness” menu, you can adjust the

brightness of the display backlight. The default

setting is “Max”.

Tone Signals

In the “Tone signal” menu, you can limit when

the measuring tool shall emit an audio signal. The

precondition for this is that the signal has not

been switched off via the audio signal button 13.

– The default setting is “Wallobjects”: An audio

signal sounds after each button press, and

whenever a wall object is under the sensor

range. Additionally, a short-beat warning sig-

nal is given for “live” wires.

– With the setting “Live wire”, an audio signal

sounds after each button press, as does the

warning signal for “live” wires (short-beat

signal), when the measuring tool indicates a

power line.

– With the setting “Keyclick”, a tone signal

only sounds after a button press.

Default Mode

In the “Defaultmode” menu, you can set the de-

fault operating mode that is to be pre-set after

switching on the measuring tool. The default

setting is “Universal mode”.

“Extended Settings” Menu

To access the “Extended settings” menu, press

the setup button 14 and the On/Off button 15 at

the same time when the measuring tool is

switched off.

To exit the menu, press the start button 11. The

standard start display for the measuring proc-

ess is activated and the settings are saved.

Navigating in the Menu

Press the setup button 14 to scroll down.

Press the selection buttons 10 and 12 to select

the values:

– Selection button 10 will select the right-hand

or next value.

– Selection button 12 will select the left-hand

or previous value.

Device Information

In the “Device Infos” menu, you can access in-

formation on the measuring tool, e.g. the “Oper-

ation Time”.

In the “Restore Settings” menu, you can restore

the factory settings.

OBJ_BUCH-844-006.book Page 25 Monday, August 30, 2010 10:44 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch D-tect 150 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info