Bedienungsanleitung Bosch DFR097T51 (Seite 12 von 16) (Englisch)

747003

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

en Installation instructions

Incorrect repairs are dangerous.

▶

Repairs to the appliance should only be

carried out by trained specialist staff.

▶

Only use genuine spare parts when repair-

ing the appliance.

▶

If the power cord of this appliance is dam-

aged, it must be replaced by the manufac-

turer, the manufacturer's Customer Service

or a similarly qualified person in order to

prevent any risk.

Improper installation is dangerous.

▶

Connect and operate the appliance only in

accordance with the specifications on the

rating plate.

▶

Connect the appliance to a power supply

with alternating current only via a properly

installed socket with earthing.

▶

The protective conductor system of the do-

mestic electrical installation must be prop-

erly installed.

▶

Never equip the appliance with an external

switching device, e.g. a timer or remote

control.

▶

When the appliance is installed, the mains

plug of the power cord must be freely ac-

cessible. If free access is not possible, an

all-pole isolating switch must be installed in

the permanent electrical installation accord-

ing to the conditions of Overvoltage Cat-

egory III and according to the installation

regulations.

▶

When installing the appliance, check that

the power cable is not trapped or dam-

aged.

12.4 Information on the installation situation

¡ Install this appliance in a kitchen cupboard.

12.5 Instructions for the exhaust air pipe

The appliance manufacturer does not provide any war-

ranty for faults attributable to the pipeline.

¡ Use a short, straight exhaust air pipe with as large a

pipe diameter as possible.

¡ Long, rough exhaust air pipes, many pipe bends or

small pipe diameters reduce the suction power and

increase the fan noise.

¡ An exhaust air pipe that is made of non-combustible

material.

¡ To prevent condensate from returning, fit the ex-

haust air pipe from the appliance with a 1° gradient.

Round pipes

Use round pipes with an inner diameter of 150mm (re-

commended) or at least 120mm.

Flat ducts

Use flat ducts with an inner cross-section that corres-

ponds to the diameter of the round pipes:

¡ Diameter of 150mm corresponds to ap-

prox.177cm².

¡ Diameter of 120mm corresponds to ap-

prox.113cm².

¡ Use sealing strips for different pipe diameters.

¡ Do not use any flat ducts with sharp bends.

12.6 Instructions for the electrical

connection

In order to be able to safely connect the appliance to

the electrical system, follow these instructions.

WARNING‒Risk of electric shock!

It must always be possible to disconnect the appliance

from the electricity supply. The appliance must only be

connected to a protective contact socket that has been

correctly installed.

▶

The mains plug for the mains power cable must be

easily accessible after the appliance is installed.

▶

If this is not possible, an all-pole isolating switch

must be integrated into the permanent electrical in-

stallation according to the conditions of overvoltage

category III and according to the installation regula-

tions.

▶

The permanent electrical installation must only be

wired by a professional electrician. We recommend

installing a residual-current circuit breaker (RCCB)

in the appliance's power supply circuit.

Sharp-edged components inside the appliance may

damage the connecting cable.

▶

Do not kink or trap the connecting cable.

¡ The connection data can be found on the rating

plate inside the appliance.

¡ To see the rating plate, remove the grease filter.

¡ The connecting cable is approx.1.30m long.

¡ This appliance complies with the EC interference

suppression regulations.

¡ The appliance corresponds to protection class 1.

Therefore, only use the appliance with a protective

earth connection.

¡ Do not connect the appliance to the power supply

during installation.

¡ Ensure that the protection against contact is guaran-

teed during installation.

12.7 General information

Follow these general instructions during the installation.

¡ For the installation, observe the currently valid build-

ing regulations and the regulations of the local elec-

tricity and gas suppliers.

¡ When discharging the exhaust air, the official and

legal regulations, such as the regional building

code., must be observed.

¡ The width of the extractor hood must correspond at

least with the width of the hob.

¡ To optimally detect the cooking vapours, install the

appliance in the middle of the hob.

¡ In order to freely access the appliance for servicing,

select an easy-to-reach installation site.

¡ The surfaces of the appliance are sensitive. Avoid

damaging them during installation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch DFR097T51 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch DFR097T51

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info