Bedienungsanleitung Bosch DHL555BAU (Seite 14 von 16) (Englisch)

773210

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

en Installation instructions

Incorrect installation is dangerous.

▶Connect and operate the appliance only in

accordance with the specifications on the

rating plate.

▶Connect the appliance to a power supply

with alternating current only via a properly

installed socket with earthing.

▶The protective conductor system of the do-

mestic electrical installation must be prop-

erly installed.

▶Never equip the appliance with an external

switching device, e.g. a timer or remote

control.

▶When the appliance is installed, the mains

plug of the power cord must be freely ac-

cessible. If free access is not possible, an

all-pole isolating switch must be installed in

the permanent electrical installation accord-

ing to the conditions of Overvoltage Cat-

egory III and according to the installation

regulations.

▶When installing the appliance, check that

the power cable is not trapped or dam-

aged.

12.6 General information

Follow these general instructions during the installation.

¡For the installation, observe the currently valid build-

ing regulations and the regulations of the local elec-

tricity and gas suppliers.

¡When discharging the exhaust air, the official and

legal regulations, such as the regional building

code., must be observed.

¡In order to freely access the appliance for servicing,

select an easy-to-reach installation site.

¡The surfaces of the appliance are sensitive. Avoid

damaging them during installation.

12.7 Instructions for the electrical

connection

In order to safely connect the appliance to the elec-

trical system, follow these instructions.

WARNING‒Risk of electric shock!

It must always be possible to disconnect the appliance

from the electricity supply. The appliance must only be

connected to a protective contact socket that has been

correctly installed.

▶The mains plug for the mains power cable must be

easily accessible after the appliance is installed.

▶If this is not possible, an all-pole isolating switch

must be integrated into the permanent electrical in-

stallation according to the conditions of overvoltage

category III and according to the installation regula-

tions.

▶The permanent electrical installation must only be

wired by a professional electrician. We recommend

installing a residual-current circuit breaker (RCCB)

in the appliance's power supply circuit.

Sharp-edged components inside the appliance may

damage the connecting cable.

▶Do not kink or trap the connecting cable.

¡The connection data can be found on the rating

plate. →Page10

¡The connecting cable is approx.1.30m long.

¡This appliance complies with the EC interference

suppression regulations.

¡The appliance corresponds to protection class 1.

You should therefore only use the appliance with a

protective earth connection.

¡Do not connect the appliance to the power supply

during installation.

¡Ensure that the protection against contact is guaran-

teed during installation.

12.8 Information on the installation

situation

¡Install this appliance in a surround.

¡To install additional special accessory parts, ob-

serve the enclosed installation instructions.

¡The width of the extractor hood must correspond at

least with the width of the hob.

¡To optimally detect the cooking vapours, install the

appliance in the middle of the hob.

12.9 Instructions for the exhaust air pipe

The appliance manufacturer does not provide any war-

ranty for faults attributable to the pipeline.

¡Use a short, straight exhaust air pipe with as large a

pipe diameter as possible.

¡Long, rough exhaust air pipes, many pipe bends or

small pipe diameters reduce the suction power and

increase the fan noise.

¡Use an exhaust pipe that is made of non-combust-

ible material.

¡To prevent condensate from returning, fit the ex-

haust pipe with a 1° gradient from the appliance.

Flat ducts

Use flat ducts with an inner cross-section that corres-

ponds to the diameter of the round pipes:

¡Diameter of 150mm corresponds to ap-

prox.177cm².

¡Diameter of 120mm corresponds to ap-

prox.113cm².

¡Use sealing strips for different pipe diameters.

¡Do not use any flat ducts with sharp bends.

Round pipes

Use round pipes with an inner diameter of 150mm (re-

commended) or at least 120mm.

12.10 Instructions for the air extraction

mode

For air extraction mode, a one-way flap should be in-

stalled.

Notes

¡If a one-way flap is not included with the appliance,

one can be ordered from a specialist retailer.

¡If the exhaust air is conveyed through the external

wall, a telescopic duct should be used.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch DHL555BAU Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info