Bedienungsanleitung Bosch DIG97IM50B (Seite 13 von 16) (Englisch)

746907

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

en General information

:Warning – Risk of electric shock!

■ Components inside the appliance may have

sharp edges. These may damage the

connecting cable. Do not kink or pinch the

connecting cable during installation.

Risk of electric shock!

■ It must always be possible to disconnect

the appliance from the electricity supply.

The appliance must only be connected to a

protective contact socket that has been

correctly installed.

The mains plug of the mains power cable

must be easily accessible after installation

of the appliance. If this is not possible, an

all-pole isolating switch must be integrated

into the permanent electrical installation

according to the conditions of overvoltage

category III and according to the installation

regulations.

The permanent electrical installation must

only be wired by a professional electrician.

We recommend installing a residual-current

circuit breaker (RCCB) in the appliance's

power supply circuit.

:Warning – Risk of electric shock!

Incorrect repairs are dangerous. Repairs may

only be carried out and damaged power

cables replaced by one of our trained after-

sales technicians. If the appliance is defective,

unplug the appliance from the mains or switch

off the circuit breaker in the fuse box. Contact

the after-sales service.

:Warning – Danger of suffocation!

Packaging material is dangerous to children.

Never allow children to play with packaging

material.

KGeneral information

Gener al i nf or mat i o n

Exhaust air mode

:Warning – Risk of death!

Risk of poisoning from flue gases that are drawn back

in. The exhaust air must not be conveyed into a

functioning smoke or exhaust gas flue or into a shaft

which is used to ventilate installation rooms that contain

heating appliances. If the exhaust air is to be conveyed

into a non-functioning smoke or exhaust gas flue, you

must obtain the consent of the heating engineer

responsible.

If the exhaust air is conveyed through the outer wall, a

telescopic wall box should be used.

Exhaust duct

Note: The device manufacturer does not assume any

warranty for complaints attributable to the pipe section.

■ The device achieves its optimum performance by

means of a short, straight exhaust air pipe and as

large a pipe diameter as possible.

■ As a result of long rough exhaust air pipes, many

pipe bends or pipe diameters that are smaller than

150 mm, the optimum extraction performance is not

achieved and fan noise is increased.

■ The pipes or hoses for laying the exhaust air line

must consist of non-combustible material.

Round pipes

An inner diameter of 150 mm, but at least 120 mm, is

recommended.

Flat ducts

The inner cross-section must correspond to the

diameter of the round pipes.

dia. 150 mm ca. 177 cm

dia. 120 mm ca. 113 cm

■ Flat ducts should not have any sharp deflections.

■ Use sealing strips for deviating pipe diameters.

Preparing the ceiling

■ The ceiling must be flat, horizontal and have

adequate load-bearing capacity.

■ The depth of the bore holes must be the same

length as the screws. The wall plugs must have a

secure grip.

■ The enclosed screws and wall plugs are suitable for

solid brickwork. Suitable fasteners must be used for

other structures (e.g. plasterboard, porous concrete,

poroton bricks).

■ The max. weight of the extractor hood is 50 kg.

Installation en

Electrical connection

:Warning – Risk of electric shock!

Components inside the appliance may have sharp

edges. These may damage the connecting cable. Do

not kink or pinch the connecting cable during

installation.

The required connection data can be found on the

rating plate inside the appliance; to do this, remove the

metal mesh grease filter.

Length of the cable: approx. 1.30 m

This appliance complies with the EC interference

suppression regulations.

:Warning – Risk of electric shock!

It must always be possible to disconnect the appliance

from the electricity supply. The appliance must only be

connected to a protective contact socket that has been

correctly installed.

The mains plug of the mains power cable must be

easily accessible after installation of the appliance. If

this is not possible, an all-pole isolating switch must be

integrated into the permanent electrical installation

according to the conditions of overvoltage category III

and according to the installation regulations.

The permanent electrical installation must only be wired

by a professional electrician. We recommend installing

a residual-current circuit breaker (RCCB) in the

appliance's power supply circuit.

5Installation

I nst al l at i on

Fitting the upper support frame

1. Before fitting, determine the total height of the

support frame and mark the screw holes.

Note: The height of the support frame can be

adjusted in 20 mm intervals.

2. On the ceiling, mark the centre point of the

appliance.

3. Using the enclosed template, mark the positions for

the screws on the ceiling.

4. Drill four 8 mm diameter holes to a depth of 80 mm

for the fasteners and press in the wall plugs flush

with the ceiling.

5. Fasten the upper part of the support frame to the

ceiling with 4 screws.

Note: Ensure that the support frame is in the correct

position. The middle bracket defines the preferred

side and must be facing the hob control elements.

[

Bosch DIG97IM50B Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch DIG97IM50B

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info