Bedienungsanleitung Bosch DWB091E59 (Seite 6 von 16) (Englisch)

533160

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Intensive setting

You can use the intensive setting if there is a large build-up of

odours and fumes/vapours.

Press the + button when the fan is at setting

„.

The intensive boost setting

‚ is activated. Pressing the + button

again activates the intensive boost

ƒsetting.

After approx. six minutes, the electronics automatically reduce

the fan to a lower setting . If you want to end the intensive

setting before the preset time expires, press the - button until

the required fan setting is reached.

Fan run-on time

The fan run-on time is possible at every fan setting (except

boost

‚ and boost ƒ).

Select the desired fan setting and press the

r button.

Šminr appears on the display.

Once this time has elapsed, the fan switches off automatically.

Setting the run-on time

When

Šminr appears on the display, press the + or - button.

You can set a run-on time of between 1 and 9 minutes.

Lighting

The lighting can be switched on and off independently of the

fan.

Press the

B button.

Setting the brightness

Press and hold the

B button until the desired brightness is

reached.

Saturation display

When the metal mesh grease filters or the activated carbon

filter are saturated, a signal sounds for approx. 4 seconds after

the fan is switched off.

In addition, the corresponding symbol appears in the display:

■ Metal mesh grease filter: #

■ Activated carbon filter: ’#

If you have not yet done so, the metal mesh grease filters

should be cleaned or the activated carbon filter changed now.

For instructions on how to clean the metal mesh grease filters,

please refer to the section Cleaning and maintenance.

While the saturation displays are flashing, they can be reset. To

do this, press the

# button.

Switching over the display for circulating-air mode

For circulating-air mode, the electronic control display must be

switched over accordingly:

■ The extractor hood must be connected and switched off.

■ Press the % and r buttons at the same time until the

™# display for starter sets for circulating-air mode or

’# display for CleanAir circulating air modules

lights up.

■ Repeatedly press the button combination to switch the

electronic control display back to exhaust air mode (

display).

Audible signal

Switching on the acoustic signal

When the fan is switched off, press the

% and + buttons at the

same time for approx. three seconds. An acknowledgement

signal sounds.

Switching off the acoustic signal

Repeat the "Switching on the acoustic signal" process.

Control panel model 3

Control panel

Setting the fan

Switching on the appliance

■ Press the % button.

The fan starts at setting

ƒ.

■ Press the + or - button to change the fan strength.

Switching off

Press the

% button.

Intensive setting

You can use the intensive setting if there is a large build-up of

odours and fumes/vapours.

Press the + button when the fan is at setting

„.

The intensive boost setting

‚ is activated. Pressing the + button

again activates the intensive boost

ƒsetting.

After approx. six minutes, the electronics automatically reduce

the fan to a lower setting . If you want to end the intensive

setting before the preset time expires, press the - button until

the required fan setting is reached.

Automatic mode

Switching on the appliance

■ Press the % button.

The fan starts at

ƒ setting.

■ Press the 1 button.

The optimum fan setting

‚, ƒ or „ is automatically set via a

sensor.

Switching off the appliance

Press the

1 or % button to switch off automatic mode.

The fan switches off automatically if the sensor no longer

detects a change in the air quality of the room.

The automatic mode lasts 4 hours at most.

Sensor control

In automatic mode, a sensor in the extractor hood detects the

intensity of the cooking and roasting fumes. Depending on the

setting of the sensor, the fan automatically switches to another

fan setting.

Default sensitivity setting:

†

Lowest sensitivity setting: ‹

Highest sensitivity setting: Š

If the sensor control responds too quickly or too slowly, it can

be changed accordingly:

Explanation

Fan on/off

Eco function (automatic mode)

- Reduce the fan settings

+ Increase the fan settings/intensive setting 1, 2

Fan run-on time

Light on/off/dimming

HFR

ERRVW

HFR

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch DWB091E59 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch DWB091E59

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info