Bedienungsanleitung Bosch DWB66IM50 (Seite 15 von 16) (Englisch)

747002

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

en Installation

Installation

1. Attaching and aligning the appliance. ¨

2. Mark the hole for the safety screw. ©

3. Remove the appliance once more. ª





[





 

! !











[





 

! !









[





 

! !





Installation en

Finishing installation of the appliance

1. Drill an 8mm Øhole to a depth of 80mm for the

safety screw and press the wall plug flush into the

wall.

2. First remove the protective foil from the back of the

appliance and, following installation, remove the foil

completely.

3. Connect the appliance. ©

4. Screw in the safety screw - and washer - and tighten

all the screws.

Exhaust duct

Note: The device manufacturer does not assume any

warranty for complaints attributable to the pipe section.

■ The device achieves its optimum performance by

means of a short, straight exhaust air pipe and as

large a pipe diameter as possible.

■ As a result of long rough exhaust air pipes, many

pipe bends or pipe diameters that are smaller than

150 mm, the optimum extraction performance is not

achieved and fan noise is increased.

■ The pipes or hoses for laying the exhaust air line

must consist of non-combustible material.

Round pipes

An inner diameter of 150 mm, but at least 120 mm, is

recommended.

Flat ducts

The inner cross-section must correspond to the

diameter of the round pipes.

dia. 150 mm ca. 177 cm

dia. 120 mm ca. 113 cm

■ Flat ducts should not have any sharp deflections.

■ Use sealing strips for deviating pipe diameters.

Connecting the appliance to the power

supply

Connecting the air extractor

Note: If using an aluminium pipe, smooth the

connection area beforehand.

1. Attach the air extractor pipe directly to the air-pipe

connector.

2. Connect to air extractor opening.

3. Seal the joints appropriately.

Connect the power supply

1. Plug the mains plug into the earthed socket.

2. If a fixed connection is required, please follow the

instructions in the Electrical Connection section.

Attaching the flue duct

:Warning – Risk of injury!

Components inside the appliance may have sharp

edges. Wear protective gloves.

1. Separate the flue duct sections.

To do this, remove the adhesive tape.

2. Remove the pieces of protective film from both flue

duct sections.

3. Push one flue duct section into the other.

Notes

– To prevent scratches, lay paper over the edges of

the outer flue duct section to protect the surface.

– The slots of the inner flue duct section should

point downwards.

4. Place the flue ducts sections on the appliance.

5. Slide the inner flue duct section upwards, and attach

it to the left and right sides of the retaining bracket.

7. Screw the flue duct section to the sides of the

retaining bracket using two screws.

8. Use two screws to fasten the outer flue duct section

to the appliance from below.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch DWB66IM50 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch DWB66IM50

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info