Bedienungsanleitung Bosch DWB98JQ50B (Seite 9 von 20) (Englisch)

746910

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

en Operating the appliance

Saturation display

If the metal grease filters or the activated charcoal filter

are/is saturated, the corresponding symbols flashes

after the appliance is switched off:

■ Metal grease filters: # and 1

■ Activated charcoal filter: # and 2

■ Metal grease filter and activated charcoal filter: #,

1 and 2

If you have not yet done so, the metal grease filters

should now be cleaned or the activated charcoal filter

replaced. ~ "Cleaning and maintenance" on page 10

Note: The saturation indicator does not apply for non-

renewable activated charcoal filters that are inserted

downstream of the metal grease filter. These activated

charcoal filters must be replaced twice a year.

The saturation indicators can be reset while they are

flashing. To do this, touch the # symbol.

Switching over the display for air recirculation mode

For air recirculation mode, the electronic controller must

be switched over accordingly:

■ The extractor hood must be connected and switched

off.

■ Touch and hold the D symbol. Touch the "2"

symbol.Take your finger off the D symbol. This

will switch the electronic controller over to air

recirculation mode (filters that cannot be

regenerated).

■ Touch and hold the D symbol. Touch the "3"

symbol.Take your finger off the D symbol. This

will switch the electronic controller over to air

recirculation mode (filters that can be regenerated).

■ Repeatedly touching and holding the D symbol

and touching the "1" symbol switches the electronic

controller back over to air extraction mode.

Audible signal

Switching on

Touch and hold the

# and y symbols at the same

time for approximately 3 seconds when the fan is

switched off. An audible signal will sound as an

acknowledgement.

Switching off

Touch and hold the

# and y symbols at the same

time for approximately 3 seconds when the fan is

switched off. An audible signal will sound as an

acknowledgement.

Operating the appliance en

Control panel model 2

Setting the fan

Switching on

Touch the

# symbol.

The fan starts at fan setting 2.

Selecting the fan setting

Touch symbol 1, 2 or 3 to set a different fan setting.

Switching off

Touch the # symbol.

Intensive setting

You can use the intensive setting if there is a large

build-up of odours and fumes/vapours.

Switching on

Touch the

C or D symbol.

Note: After approx. 6 minutes, the extractor hood

automatically switches back to fan setting 3.

Switching off

If you want to end intensive mode before the preset

time expires, touch the symbol for the required fan

setting.

Fan run-on time

Switching on

Touch the y symbol.

The fan will run at fan setting 1.

After approximately 10 minutes, the fan will switch itself

off automatically.

Switching off

Touch the y symbol.

This immediately stops fan run-on.

Automatic mode

Switching on

1. Touch the # symbol.

The fan will start at setting 2.

2. Touch the > symbol.

The optimum fan setting is set automatically using

the PerfectAir sensor.

Switching off

Touch # or any fan setting to switch off automatic

mode.

The fan switches itself off automatically if the PerfectAir

sensor detects no further change in the air quality in the

room.

Automatic mode can run for a maximum of 4 hours.

Sensor control

In automatic mode, the PerfectAir sensor in the

extractor hood detects the intensity of the cooking and

roasting odours. Depending on the setting of the

PerfectAir sensor, the fan automatically switches itself to

another fan setting.

Possible sensor settings:

Default sensitivity setting:

„ (fan setting 3)

Lowest sensitivity setting: ‚ (fan setting 1)

Highest sensitivity setting: † (fan setting D)

If the sensor controller responds too strongly or not

enough, it can be changed accordingly:

1. Touch and hold the > symbol when the fan is

switched off. The setting will be displayed.

2. The sensor controller setting can be changed by

touching symbols 1, 2, 3, C or D.

3. Take your finger off the > symbol.

Symbol Explanation

Fan on/off

1-3 Fan settings

Intensive mode 1

Intensive mode 2

Fan run-on

Automatic mode

Metal grease filter saturation indicator

Activated charcoal filter saturation indicator

Light on/off/dimming

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch DWB98JQ50B Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch DWB98JQ50B

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info