Bedienungsanleitung Bosch DWB98PR50 (Seite 9 von 24) (Englisch)

746998

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

en Operating the appliance

Sensor control

In automatic mode, the PerfectAir sensor in the

extractor hood detects the intensity of the cooking and

roasting odours. Depending on the setting of the

PerfectAir sensor, the fan automatically switches itself to

another fan setting.

Possible sensor settings:

Default sensitivity setting:

„ (fan setting 3)

Lowest sensitivity setting: ‚ (fan setting 1)

Highest sensitivity setting: † (fan setting D)

If the sensor controller responds too strongly or not

enough, it can be changed accordingly:

1. Touch and hold the > symbol when the fan is

switched off. The setting will be displayed.

2. The sensor controller setting can be changed by

touching symbols 1, 2, 3,

C or D.

3. Take your finger off the > symbol.

Saturation display

If the metal grease filters or the activated charcoal filter

are/is saturated, the corresponding symbols flashes

after the appliance is switched off:

■ Metal grease filters: # and 1

■ Activated charcoal filter: # and 2

■ Metal grease filter and activated charcoal filter: #,

1 and 2

If you have not yet done so, the metal grease filters

should now be cleaned or the activated charcoal filter

replaced. ~ "Cleaning and maintenance" on page 12

Note: The saturation indicator does not apply for non-

renewable activated charcoal filters that are inserted

downstream of the metal grease filter. These activated

charcoal filters must be replaced twice a year.

The saturation indicators can be reset while they are

flashing. To do this, touch the # symbol.

Switching over the display for air recirculation mode

For air recirculation mode, the electronic controller must

be switched over accordingly:

■ The extractor hood must be connected and switched

off.

■ Touch and hold the D symbol. Touch the "2"

symbol.Take your finger off the D symbol. This

will switch the electronic controller over to air

recirculation mode (filters that cannot be

regenerated).

■ Touch and hold the D symbol. Touch the "3"

symbol.Take your finger off the D symbol. This

will switch the electronic controller over to air

recirculation mode (filters that can be regenerated).

■ Repeatedly touching and holding the D symbol

and touching the "1" symbol switches the electronic

controller back over to air extraction mode.

Lighting

The lighting can be switched on and off independently

of the fan.

Touch the

B symbol.

Setting the brightness

Press and hold the B symbol until the required

brightness is reached.

Audible signal

Switching on

Touch and hold the

# and y symbols at the same

time for approximately 3 seconds when the fan is

switched off. An audible signal will sound as an

acknowledgement.

Switching off

Touch and hold the # and y symbols at the same

time for approximately 3 seconds when the fan is

switched off. An audible signal will sound as an

acknowledgement.

Connecting to a hob en

eConnecting to a hob

Connect i ng to a hob

You can connect this appliance to a hob (if the hob

supports connection to the appliance) and then control

the functions of the hood via your hob.

Appliances can be connected to each other in different

ways:

Home Connect

Two appliances can be connected using the Home

Connect app provided that both of them are Home

Connect compatible.

Refer to the Home Connect documents supplied for

more information.

Connecting appliances directly

If the appliance is connected directly to a hob, it cannot

be connected to your home network as well. The

appliance will function as an extractor hood that is not

connected to the network and you can continue to

operate it via the control panel.

Connecting appliances via your home network

If the appliances are connected to each other via your

home network, both the hood controls on the hob and

Home Connect can be used to operate the appliance.

Notes

■ Make sure you follow the safety instructions in the

instruction manual for your extractor hood and that

these are complied with even when operating the

appliance via the hood controls on the hob.

■ If the extractor hood is being operated by means of

the controls on the hood itself, this mode of

operation always has priority. It is not possible to use

the hood controls on the hob during this time.

Setting up a connection

The hood must be switched off before you can connect

the hob and extractor hood.

Connecting directly

Make sure that the hob is switched on and is in search

mode.

To do this, refer to the section entitled "Connecting to

the extractor hood" in the instruction manual for your

hob.

Notes

■ Before connecting the appliance, reset all existing

connections to the WiFi or other appliances.

■ If your extractor hood is connected directly to the

hob, it cannot be connected to your WiFi as well and

you will not be able to use Home Connect.

Press and hold the

D symbol until it starts to flash.

The extractor hood has been connected to the hob

when the D symbol stops flashing and remains

continuously lit.

Connecting via your home network

Follow the instructions in the section entitled "Automatic

your home network" ~ "Home Connect" on page 10

Once the extractor hood is connected to your home

network, you can connect to the hob via the Home

Connect app. To do this. follow the instructions on your

mobile device.





Bosch DWB98PR50 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch DWB98PR50

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info