Bedienungsanleitung Bosch DWK 063650 (Seite 23 von 52) (Deutsch, Englisch, Holländisch, Französisch)

108258

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Prior to installation

 Round pipes:

We recommend

Internal diameter: 150 mm (at least 120 mm).

 Flat ducts must have an internal crosssection

that equates to that of round pipes.

There should be no sharp bends.

ø 120 mm approx. 113 cm

ø 150 mm approx. 177 cm

 If pipes have different diameters: Insert seal-

ing strip.

 For exhaust-air mode, ensure that there is an

adequate supply of fresh air.

Connecting a Ø 150 mm exhaust-air pipe:

 Mount the pipe directly onto the air outlet on the

hood.

Connecting a Ø 120 mm exhaust-air pipe:

 Attach the reducing con-

nector directly to the air

pipe.

 Attach the exhaust-air

pipe to the reducing con-

nector.

Circulating-air mode

 With activated carbon ﬁ lter if exhaust-air mode

is not possible.

The complete installation set can

be obtained from specialist outlets.

The corresponding accessory numbers

can be found at the end of these oper-

ating instructions.

Electrical connection

WARNING: THIS APPLIANCE MUST BE

EARTHED

IMPORTANT: Fitting a Different Plug:

The wires in the mains lead are coloured in accord-

ance with the following code:

Green and Yellow – Earth

Blue – Neutral

Brown – Live

If you ﬁ t your own plug, the colours of these wires

may not correspond with the identifying marks on

the plug terminals.

This is what you have to do:

1. Connect the green and yellow (Earth) wire to

the terminal in the plug marked ‘E’ or with the

symbol ( ), or coloured green or green and yel-

low.

2. Connect the blue (Neutral) wire to the terminal

in the plug marked ‘N’ or coloured black.

3. Connect the brown (Live) wire to the terminal

marked ‘L’, or coloured red.

The extractor hood should only be connected to an

earthed socket that has been installed according to

relevant regulations.

If possible, site the earthed socket directly behind

the chimney panelling.

 The earthed socket should be connected via its

own circuit.

 If the earthed socket is no longer accessible fol-

lowing installation of the extractor hood, ensure

that there is a permanently installed disconnec-

tor.

If it is necessary to wire the extractor hood di-

rectly into the mains:

The extractor hood should only be connected to the

electricity supply by a properly qualiﬁ ed electrician.

A separator must be installed in the household

circuit. A suitable separator is a switch that has a

contact gap of more than 3 mm and interrupts all

poles. Such devices include circuit breakers and

contactors.

If the connecting cable for this appliance

is damaged, the cable must be replaced by the

manufacturer or his customer service or a similarly

qualiﬁ ed person in order to prevent serious injury to

the user.

Preparing the wall

 The wall must be ﬂ at and perpendicular.

 Ensure that the wall is capable of providing a

ﬁ rm hold for mounting screws and plugs.

Weight in kg: 20.

We reserve the right to construction changes within

the context of technical development.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch DWK 063650 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info