Bedienungsanleitung Bosch DWK098E51 (Seite 7 von 16) (Englisch)

533169

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

1. When the fan is switched off, press the 1 button and hold it

for approx. 4 seconds. The setting is displayed.

2. Press the + or - button to change the setting of the sensor

control.

3. To confirm the entries, press and hold the 1 button for

approx. 4 seconds.

Fan run-on time

The fan run-on time is possible at every fan setting (except

boost

‚ and boost ƒ).

Select the desired fan setting and press the

r button.

Šminr appears on the display.

Once this time has elapsed, the fan switches off automatically.

Setting the run-on time

When

Šminr appears on the display, press the + or - button.

You can set a run-on time of between 1 and 9 minutes.

Lighting

The lighting can be switched on and off independently of the

fan.

Press the

B button.

Setting the brightness

Press and hold the

B button until the desired brightness is

reached.

Saturation display

When the metal mesh grease filters or the activated carbon

filter are saturated, a signal sounds for approx. 4 seconds after

the fan is switched off.

In addition, the corresponding symbol appears in the display:

■ Metal mesh grease filter: #

■ Activated carbon filter: ’#

If you have not yet done so, the metal mesh grease filters

should be cleaned or the activated carbon filter changed now.

For instructions on how to clean the metal mesh grease filters,

please refer to the section Cleaning and maintenance.

While the saturation displays are flashing, they can be reset. To

do this, press the – button.

Switching over the display for circulating-air mode

For circulating-air mode, the electronic control display must be

switched over accordingly:

■ The extractor hood must be connected and switched off.

■ Press the % and r buttons at the same time until the

™# display for starter sets for circulating-air mode or

’# display for CleanAir circulating air modules

lights up.

■ Repeatedly press the button combination to switch the

electronic control display back to exhaust air mode (

display).

Audible signal

Switching on the acoustic signal

When the fan is switched off, press the

% and + buttons at the

same time for approx. three seconds. An acknowledgement

signal sounds.

Switching off the acoustic signal

Repeat the "Switching on the acoustic signal" process.

Cleaning and maintenance

: Risk of burns!

The appliance will become hot during operation, especially

near the bulbs. Allow the appliance to cool down before

cleaning.

: Risk of electric shock!

Penetrating moisture may result in an electric shock. Clean the

appliance using a damp cloth only. Before cleaning, pull out the

mains plug or switch off the circuit breaker in the fuse box.

: Risk of electric shock!

Penetrating moisture may cause an electric shock. Do not use

any high-pressure cleaners or steam cleaners.

: Risk of injury!

Components inside the appliance may have sharp edges. Wear

protective gloves.

Cleaning agents

Observe the information in the table to ensure that the different

surfaces are not damaged by using the wrong type of cleaning

agent. Do not use

■ harsh or abrasive cleaning agents,

■ cleaning agents with a high concentration of alcohol,

■ hard scouring pads or sponges,

■ high-pressure cleaners or steam cleaners.

Wash new sponge cloths thoroughly before use.

Follow all instructions and warnings included with the cleaning

agents.

Area Cleaning agents

Stainless steel Hot soapy water:

Clean with a dish cloth and dry with a

soft cloth.

Clean stainless steel surfaces in the

direction of the grain only.

Special stainless steel cleaning prod-

ucts are available from our after-sales

service or from specialist retailers.

Apply a very thin layer of the cleaning

product with a soft cloth.

Painted surfaces Hot soapy water:

Clean using a damp dish cloth and

dry with a soft cloth/towel.

Do not use any stainless steel cleaners.

Aluminium and

plastic

Glass cleaner:

Clean with a soft cloth.

Glass Glass cleaner:

Clean with a soft cloth. Do not use a

glass scraper.

Operating controls Hot soapy water:

Clean using a damp dish cloth and

dry with a soft cloth.

Risk of damage to the electronics

from penetrating moisture. Never

clean operator controls with a wet

cloth.

Do not use any stainless steel cleaners.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch DWK098E51 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch DWK098E51

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info