Bedienungsanleitung Bosch EasyControl CT200B (Seite 8 von 12) (Englisch)

697141

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

EasyControl – 6720818479 (2017/10)

Specifications

7Specifications

8 Maintenance and faults

8.1 New Wi-Fi network or new network password

To log EasyControl onto a new Wi-Fi network, or if the existing network

has a new password:

▶ Reset EasyControl ( section 8.3).

▶ Perform the following steps to create a Wi-Fi network

( section 5.4).

8.2 Power failure

All the settings are retained after a power failure. After renewed

connection with the Wi-Fi network, all the settings are synchronised with

the Bosch server.

▶ Check the date and time.

8.3 Reset

If EasyControl no longer functions correctly:

▶ Lift the EasyControl briefly from the plinth ( fig. 7, page 5).

If the problem persists:

▶ Press the Reset button ( fig. 19) and hold for several seconds.

Please note! This means that all personalised settings are deleted,

and the Wi-Fi connection must be established again.

If the problem persists:

▶ Consult the installer or manufacturer.

Fig. 19 Reset

8.4 Faults

The fault displays for the heat source are visible on the touch screen and

are sent automatically from the controller to the EasyControl app.

Contact with the installer can be selected in the app.

There is an extensive list on the EasyControl site with solutions for any

problems with EasyControl that may arise

Controller.

Description Unit Value

U V

14.3 – 16.0

max

W 0.9

m g (lb) 250 (0.551)

f (RF) MHz f = 868.3 … 869.5 [EU]

amb

°C (°F) 0 … 45 (32 … 113)

IP class IP30

 % RH 10 … 90

Wi-Fi f = 2.4 GHz IEEE 802.11b/g/n

Zigbee f = 2.4 GHz IEEE 802.15.4

mm (inches) h = 145 (5.7)

w =100 (3.9)

d = 27 (1.1)

Table 3

6720818478-16.1TD

1) See the back of this document for the web address.

Fault Remedy

No Wi-Fi connection. The Wi-Fi signal for the Wi-Fi router may

be too weak. Install a Wi-Fi amplifier.

Wi-Fi network

not found

The “Hide” function for the Wi-Fi router is possibly switched

on, or the “Broadcast” function (sending SSID) may be

switched off. Temporarily switch off the “Hide” function or

switch on the “Broadcast” function.

No connection to the Internet server. Wait until the

connection to the Internet server has been automatically

restored. Even without a server connection, the heat source

can be controlled in manual operation or via the time

program after it has been put into operation.

Forgotten

serial number

and access

code

The serial number and access code are on the sticker, which

is on the front of the brief installation instructions, and on the

sticker at the back of the EasyControl. If the app is used to log

on, the serial number and access code can be displayed in

the app, by navigating via the “Info menu” to the “Product

information” submenu. If the serial number and access code

can not be found, please contact “Consumer Info”

The app has no

contact with

the

EasyControl

Does the EasyControl have a connection to the Internet

( section 5.4)? Serial number and access code entered?

Please note, these are capital letter sensitive. There is

possibly a slow Internet connection. Wait for a few minutes.

The displayed

temperature is

too high or too

low

The displayed temperature can be set in the app or on the

EasyControl site

The touch

screen does not

function

If the touch screen does not detect anything for more than

5 minutes, it automatically switches itself off. After this, the

touch screen can only be activated again by touching it.

Password with

$ character

EasyControl uses the standard Wi-Fi protocol. Do not

therefore use any $ characters in the Wi-Fi network

password. Remove the $ character from the network

password.

App is not fully

functioning

It is possible that, when delivered, the EasyControl does not

yet have the current software version. This means that

possibly not all app functions can be used. The software

update occurs automatically and make take a few days.

Display of one of the following messages: repeated ignition

attempts, dripping/leaking DHW tap, too little flow through

the heating system, leak in the heating system, boiler

pressure too low, or heat source shows the Service display.

These are informative signals. The floor-standing boiler is

functioning normally.

No software

updates have

been received

from

EasyControl

Software updates are performed automatically. This requires

a continuous Internet connection. If the router is provided

with a timer, updates can be missed.

Table 4 Fault overview (the symbols are displayed on the touch screen)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch EasyControl CT200B Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch EasyControl CT200B

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info